HF Scientific 28052 MTOL+ Online Process Turbidimeter, ... - hf scientific turbidimeter
Wilkins model 70 replacement
I thought I was going to have to use one pipe wrench to hold the main body of the regulator while I used the other pipe wrench to turn the top piece of the regulator, but the pipes going into and out of the regulator seamed sturdy enough.
I used a water pressure gauge to help trouble shoot the main problem and to make sure I adjusted the rebuilt regulator to the right pressure.
Watts pressure reducing ValveRepair Kit
I used the 9/16" wrench to loosen the jam nut and then remove the pressure adjustment screw. I started loosening the top piece of the regulator by using a pipe wrench. I found that it was easier to use channel lock plyers. Carefully remove the top piece because there is a spring, a washer, and metal piece that will fall out. I found that the main spring was broken and this was probably the main reason that my water flow had decreased. I then used the channel lock plyers to remove the basket from the regulator main body.
rk1-70xl
I turned on the main water to help flush out the main body of the regulator. To keep from making a mess, I used a piece of plastic to direct the water into a bucket. After rinsing out the regulator, I used an old t-shirt to clean out the inside of the regulator.
Waterpressureregulator
*This list may vary, as names not appearing on this list are entitled to the acknowledgment of their Trademarks by M&M Control Service, Inc.
The top o-ring, of the basket, needs to be lubricated before being inserted. The rebuild kit came with a small packet of silicone lube. After inserting the basket there is a washer that goes on top of the basket. Then the spring, spring top piece, and regulator top piece screw on top. This is easier if you have the pressure screw turned almost all the way out so there is hardly any pressure on the spring.
Turn the water back on by opening the main water valve. Check the water pressure with the gauge. Slowly tighten the water pressure regulator adjustment screw clockwise until you have your desired water pressure. I found out the correct pressure should be between 70 and 85 psi. It may be different for you depending on your house and where you live.
ASME Section IV listed and rated for emergency steam discharge. Bronze body, brass and/or stainless steel internal components, silicone seat disc and stainless steel spring. "Pop" type action provides maximum safety. F-30 set at 30 psi only.
Before taking apart plumbing, it is important to shut off the main water supply and relieve the pressure in the pipes. My main shut off valve is right beside the water pressure regulator. After closing the main water valve, I relieved the pressure, in the pipes, by opening a water valve and letting the water run until the pressure was relieved.
Zurn NR3XLRepair Kit
Iron body construction. Bronze body option available in some sizes. Brass seat, silicone seat disc and EP diaphragm. "Pop" type opening action. The F-95 Valve series offers a complete line of boiler safety relief valves in sizes ranging from 3/4" X 1" to 2" X 2-1/2". This complete range of sizes provides pressure protection for many commercial/industrial OEM boilers and hot water heating system applications. 30 to 75 psi pressure sets available.
WARNING: Some of the products we sell can expose you to chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Contact your sales rep or go to www.P65Warnings.ca.gov for more information.
Wilkins NR3repair kit
Prevents internal vacuum conditions that could collapse storage tanks - especially copper. Bronze body with a male inlet, integral body seat and silicone seat disc. Maximum water pressure 200 psi. Maximum temperature 210°F (99°C). Capacity 13 SCFM at 2" Hg. Available with dust cover.
I should have gotten a large adjustable wrench for the top piece of the regulator, but instead used channel lock plyers.
Rebuilding a water pressure regulator valve is easier than replacing one. I will show you how I rebuilt my water pressure regulator.
Small, low-cost relief valves suitable for static over-pressure protection. Type FWC incorporates a calibrated adjusting screw for occasional changes in pressure setting without the use of a pressure gauge. Bronze bodies with male inlet and female outlet, silicone seats and stainless steel spring. Standard factory set is 125 psi. Available set range for FW is 15 to 250 psi. FWC is 25 to 175 psi.
Cash Acme pressureregulatorrebuildkit
The first sign that something was wrong was there seamed to be a loss of water pressure in my house. Taking a shower, seamed like there was hardly any pressure. I hooked up the water pressure gauge and found that the pressure was fine. Running the water, into a bucket, made it easy to see that the flow of water was slower than it should be. I asked a neighbor if he was experiencing any loss in pressure or flow, since we are on the same water supply. He said that his water pressure and flow was fine. That removed the possibility that the problem may have been the water supply pressure or flow. This led me to believe that there was something wrong with my water pressure regulator.
(PowersTM, also known as, POWERS REGULATOR, MCC POWERS, POWERS-FIAT, POWERS PROCESS CONTROLS, CRANE POWERS and POWERS, a Watts Industries Company. The POWERS trademark is owned by Powers, A Division of Watts Water Technologies, Inc. M&M Control Service, Inc. Is a Stocking Distributor for PowersTM)
Once reaching the desired pressure, I let the water run for a bit and then double checked the pressure. I also checked to make sure there were no water leaks at the pressure regulator valve.
Cash Acme EB45repair kit
CSA design certified per ANSI Z21.22 Relief Valves for Hot Water Supply Systems. Bronze body, stainless steel spring, furnished with silicone seat disc and EP diaphragm, as well as a test lever. Standard factory setting is 150 psi. Temperature relief setting is 210°F (99°C). All FVX Series valves through 1-1/4" have coated thermal elements that protect against mineral build-up. The 1-1/2" and 2" valves have stainless steel elements. Available with male or female inlet connections. Female outlet connections.
M&M Control Service, Inc. does not represent or claim any affiliation, association, connection or approvals with or from any manufacturer unless stated. We fully acknowledge all trademarks and/or names which are pictured and/or listed throughout the M&M Control Service, Inc. Website.
Bronze body, brass and stainless steel internal parts, silicone seat disc, and stainless steel spring. Test lever is standard on the FWL-2. Male inlet and female outlet. Automatic reseating after pressure relief. Compact and economical. The FWOL is available without the lift lever.
The NCLX incorporates an inert thermal element coating that provides effective isolation from mineral deposits (liming). Cast bronze body with male inlet and female outlet, brass and stainless steel internal parts, silicone seat disc and stainless steel spring. Test lever standard. Temperature relief setting is 210°F (99°C).