AmesBackflow 3000SS

... Valves, Vents & Drains Manual Air Vent Kit (22mm) - VBS61M. Manual Air Vent Kit (22mm). Grant. Manual Air Vent Kit (22mm). Product ...

Watts now manufactures and sells an impressive product line that plays a critical role in keeping fire protection systems operational. Watts offers a line of valves that maintain pressure in a system, as well as backflow preventers that protect water supplies. Watts Water Technologies also manufactures and sells in-building risers as well as custom engineered fire protection products.

solid set pressure regulators. Senninger® black and white pressure regulators are renowned for their accuracy, durability, and ability to maintain the overall ...

Ames3000SS spec Sheet

Find the Watts LFUSG-B-QC-SC-M2 Valve for sale here. Trusted plumbing supply online distributor.

Ames3000 DCDA

Buy Watts 3/4 In 40XL-8-100210 3/4 Temperature Pressure Relief Valve 0158675 from family-owned BC company Andrew Sheret Limited. Pickup in-store or delivery ...

8"ames3000ss

The half inch water pipe had a 3/4 inch Watt regulator installed by plumber many years ago. ... 3/4 prv · water pressure regulator · pressure regulator · water ...

Enter the system flow in the box below to determine the proper Spirovent Air Eliminator in both our standard and HV models.

Watts staff explained that Watts has had a reputation as an innovator in backflow prevention and in-building risers since the 1980s. Staff shared that Watts Water Technologies was the first company to make its backflow preventers and risers out of stainless steel, which is important because not only is stainless steel lighter and easier to install and replace, but it is corrosion resistant and lasts a long time.

Watts Water Technologies operates across the globe and is headquartered in North Andover, Massachusetts with Ames’ factory located in the Sacramento, California, area, as well as factories in New Hampshire and the Carolinas.

The Watts team shared that Watts Water Technologies has been heavily involved with the National Fire Sprinkler Association since the company joined in 1989. Rick Kelly sits on NFSA’s SAM Council, and Watts Water has exhibited numerous times at NFSA’s expos and conferences. Additionally, the entire Watts Water Technologies team has membership accounts with the NFSA and is a presence at NFSA’s chapter meetings. The Watts team shared that NFSA’s events are a great way to interact with customers and NFSA’s Learning and Development has been a great tool as well.

6"ames3000ss

The height of the toilet waste pipe may need to be adjusted if a cast iron elbow is used. NOTE: Use double studs on either side of the stud pocket. Construct ...

4"ames3000ss

LINER MANUFACTURER. 1" WELD STRIP. REVISIONS. 06/20/2014. SPECIAL ACID-RESISTANT LINING. ALL MANHOLES. PIPE PENETRATION. GROUT AS REQ'D. DRWG. NO. D-210-5.

Surprisingly, Watts Water Technologies did not start in fire protection, but rather as a plumbing company that manufactured pressure reducing valves (PRVs). In 1974 when Congress passed the Safe Water Drinking Act, it opened a new market for Watts Water Technologies. Watts acquired Ames Fire & Waterworks and added the company’s product line to their inventory.

18.1M-1996, ASSE 1016-1996, CSA B125-93, Showerhead: GSA A-A-240, ASSE seal authorized, City of L.A. approved, CSA certified, and IAPMO listed. ADA ...

For more information on Watts Water Technologies visit their site here. For more information on their Ames fire protection product line, visit this page.

15 Feb 2016 — The standard requires that the pressure drop of the water softener must not exceed 15 psi at the manufacturer's rated service flow, which must ...

NFSA staff had the pleasure of sitting down with Watts Water Technologies. Watts Water Technologies has been a Supplier and Manufacturer (SAM) member with the National Fire Sprinkler Association since 1989 and has been heavily involved with the NFSA since!