Air oil Separatorfor diesel engine

If you have an air-oil separator on your aircraft, you should install a temporary temperature gauge on the separator unit itself so that you can monitor the temperature in normal cruise conditions. If your separator unit is around 212°F or less, you may need to relocate it to a spot where it gets less cooling air flow and/or more engine heat.

Air oil separatorvs catch can

I think you might have misunderstood. My proposal is to eliminate the return line so that nothing goes back into the engine. The condensed oil is stored in a container and manually purged, and only the combustion gases are blown out the breather.

Air Oil separatorfilter

Join 110,000 readers each month and get the latest news and entertainment from the world of general aviation direct to your inbox, daily. Sign up here.

The pilot had gone to all of the work to get the crankcase oil temperature up to boil off the moisture, but the separator just returned it to the crankcase.

The problem was that the separator unit was not located in the proper location, so it was running at a temperature that condensed both the oil and the water vapor in the blow-by gases and returned it to the crankcase.

Because, in the meantime, the water goes back into the engine – which is what the return line is for. It’s useless to have a hot engine that vaporises water only to have it condense and sent back into the engine

Air oil separatorhow it works

The temp checking sounds like a perfect job for the temp tell tapes I have seen on helicopters or maybe those temp crayons…

Air oil separator aircompressor

Many people will install the unit in a more convenient location where cool air may reduce the temperature enough so that the unit can condense the water vapor.

Air Oil SeparatorWRX

This “blow-by” will usually vaporize some engine oil that is in the ring belt area. When the blow-by reaches the crankcase, it is sucked out the breather tube into the atmosphere where the oil is instantly condensed and usually sticks to the belly of your aircraft.

As an aircraft engine increases in hours, it may see increased ring wear, which can reduce the sealing performance of the engine. This means that more combustion gases get past the rings and blow into the crankcase.

Many years ago, we found some engines with air-oil separators that were having rusting problems even though the oil temperatures were in that 180°F range.

Some people say that the oil will make your aircraft slippery so it goes through the air better, but most people do not like the looks of it and the fact that the plane “marks its territory” once it is parked.

Badoil separatorsymptoms

© 2023 Cleaners Supermarket Pty Ltd. All Rights ReservedThe Extra Ordinary Cleaning Supplies Shop in NSW Australia Since 2003

To reduce this problem, some people have installed air-oil separators. The principle for these separators is that they are designed to cool the blow-by gas leaving the engine so that the oil will condense back to a liquid state.

In one of my recent columns, I wrote about the importance of getting your oil temperature up to around 180°F so that your engine would boil off the moisture in your crankcase. This is critical for all engines, but for engines with air-oil separators, that may not be enough.

Good answer Jeff, I did just that and it is still working today that was over twenty years ago..My container is a large bud light can..works great.

Why not just capture the condensed material in a canister that you periodically empty rather than piping it back into the engine at all? No belly mess and no added corrosion concerns…

What isanoil separatoron a car

So are air-oil separators bad? No, but it is very critical that they are installed correctly so that the separator unit is well above 212°F during flight, even in cool weather.

Ben Visser is an aviation fuels and lubricants expert who spent 33 years with Shell Oil. He has been a private pilot since 1985.

On one of these aircraft, they installed a container between the separator unit and the crankcase. I was shocked when we looked at what was in the container. It was a mixture of water and oil that looked like dirty mayonnaise.

The equipment is set up in such a way so that the condensed oil is returned to the crankcase and then only the combustion gases are blown out the breather. Does anyone see a problem here?