Pure Water Filterfor home

So why does the water coming from your “hot”-water faucet or shower run cold at first before finally turning hot? When that outlet was last turned on, hot water flowed through the pipes, right?

One type of recirculation system — and the focus of this blog — is a closed-loop, pump-assisted, hot-water recirculation system.

What could be simpler than the installation of a drinking water faucet with above-counter filter changes and the full protection offered by activated carbon filtration? This unique water filter does not require under-counter access or the clutter of filters and tanks typical of other water purification systems. With just a simple quarter turn at the faucet, the filter lifts out, slips off, and receives the new filter. In less than 20 seconds, it is ready to produce purified water. And, awarded the "PEOPLES CHOICE AWARD" at the Newport International Boat Show for 2016

It’s safe to say we’ve all experienced the inconvenience of having to wait for hot water to arrive at the faucet or shower — most of us every morning. You’ve probably grown accustomed to waiting several seconds or even a minute or two, depending on the distance to your bathroom or kitchen from your water heater in your basement, garage or utility closet on the opposite side of the house. The longer that distance, the longer the wait, the bigger the annoyance.

The PureWater+™ system is compact and easy to install. Once installed, filter changes and other maintenance are simple and quickly done.

Pure waterSystems reverse osmosis

But once the outlet was shut off, the remaining warm water in the pipes did not return to the water heater for reheating. Instead, it stayed in the pipes and eventually turned cold. When the outlet was next turned on, this resting cold water exited the pipes first, ahead of the incoming hot water from the water heater.

Some recirculation pumps can serve as a separate, add-on component that uses a dedicated pipe loop for hot-water recirculation.

Hot-water recirculation dramatically reduces water waste. With time and temperature sensors, hot-water recirculation pumps can control when the recirculation kicks on, ensuring that energy is not constantly being wasted.

Pure water filterfor Sink

The most efficient “traditional” recirculation method would use a combination of both a temperature sensor and a timer to activate the system.

A hot-water recirculation system delivers hot water to a faucet, shower or appliance in seconds, eliminating the usual water-wasting wait. The system does so by recirculating the water that remained in the pipes and eventually turned cold, back to the water heater, through either the cold-water line or a dedicated return line.

Pure waterproducts

Another option is to purchase a “crossover kit” that is sold with the water heater and acts as a substitute for a return line.

Not only is this inconvenient (and downright uncomfortable if you’re standing in the shower), but a typical American home annually wastes thousands of gallons of perfectly usable potable water down the drain, thanks to lengthy wait times at hot-water outlets in the bath and kitchen.

A recirculation pump can operate 24/7. But the energy savings would be nonexistent if the external circulator were always on and continuously recirculating hot water.

So what’s the solution? Is it possible to get truly “instantaneous” hot water? Yes, with a hot-water recirculation system that delivers hot water with virtually no wait time.

Whether you choose to install an external recirculation pump or go with a fully integrated system, the benefits for both are clear. A hot-water recirculation pump eliminates the need to wait for hot water by recirculating the water through your plumbing system, keeping hot water flowing and ready for the moment someone turns on the faucet or shower.

Pure waterproducts, llc

Pure Water FilterCartridges

Instead of wasting energy by having hot water flow through the system continuously, some water heaters have an integral display on the front of the unit that allows homeowners to program the recirculation system to operate at specified times.

The new PureWater+™ by forespar® combines space-saving sensibility with ease-of-use filter changes through a patented quick-connect design all performed above the countertop. The PureWater+™ does not require under-counter filter access or a reservoir apparatus similar to other plumbed-in water purifiers, all with the full protection of carbon-block filtration.

Some hot-water recirculation pumps are built into the water heater itself. An integrated recirculation pump is ideal if your home lacks a dedicated return line, and you want to avoid the cost of adding one.