MasterMixing Valve

Piping Components – A Strainer is required upstream of the PRVs to keep them clear of trash. Pressure gauges are required on both the high-pressure and low-pressure sides of the PRVs to see what the pressure drop across the valve is.  Isolation valves on all PRVs and relief valves are required for maintenance.

Thermostaticmixing valve

Watts 007M2QT 1-1/4" Double Check Assembly Valve ... Watts T063232 In Double Check Valve Backflow Preventer Assembly, Quarter Turn Shutoff, Smart Enabled Ready, 1 ...

Relief Valve – Relief valves are required downstream of the PRVs to prevent over-pressurization when the PRV fails. A pilot-operated valve can be used (ex. Cla-Val Model 50-01), but we recommend a direct-acting valve like the Cla-Val Model 55B.

Pressure Reducing Valves – stations are designed with a High-Flow and Low-Flow PRV that work in parallel to maintain a constant pressure downstream across the flow load profile of the zone. Low-Flow valves are typically direct-acting (ex. Cla-Val Model CRD-L), and High-Flow valves are pilot-operated (ex. Cla-Val Model 90-01); however actual valve selections depend on the flow and pressure drop of each station.

2024930 — tekmar Invita WiFi Thermostat 564. providing a smart solution for HVAC contractors facing wiring challenges! This thermostat ingeniously ...

3/8mixing valve

Mixing Valvefor sink

Block Valve and Control Panel – The addition of a pressure switch, control panel, and block valve can add additional safety and monitoring to the PRV Station. When a PRV fails, the pressure switch detects the high pressure and sends a signal to the control panel. This triggers the panel alarms (local and BAS output) and closes the block valve to shut down the water supply to the zone.

Whether you need a solution that provides anti-scald protection at the heat source, the point-of-use, or somewhere in between, Cash Acme has the TMV plumbing solution to fit your needs.

Eaton's Butterfly Valve Type Model 52 duplex basket strainers remove damage causing particulate matter from the system flow. Perforated or mesh stainless ...

2018112 — The general rule of thumb for proper capacity of expansion is 12% of total coolant volume for draw down and 6% of the total volume for thermal expansion.

Mixing valvefor boiler

We provide the complete cleaning and recharging of acid neutralization tanks in accordance with manufacturers specifications. ... Russell Reid is an expert in ...

3/4mixing valve

Mixing valvefor water heater

Flo-Max's precision engineering can optimise your small to medium industrial operations. Whether you require efficient drainage, circulation or irrigation, we ...

WaterMixing Valve

Cash Acme temperature mixing valves are manufactured according to ISO 9001 standard, ASSE / IAPMO / CAS fully certified, and come preset at 120 F to fit standard U.S. and Canadian plumbing codes. Each thermostatic mixing valve is tested for function, safety, and performance before leaving our factory.

Pressure Reducing Valve (PRV) Stations are an essential component of a water-distribution system in a commercial building. The 2015 Uniform Plumbing Code Section 608.2 states that PRVs are required at any point where the system static pressure exceeds 80 PSI. Typically, this applies to mid- and high-rise buildings when the pressure boost to serve the upper floors is over 80 PSI. It takes a combination of valves and safety devices to create a Pressure Reducing Station.

Series 174A resists corrosive water conditions, sticking and freezing and it prevents water and sediment from being trapped in the seat. It is designed for ...

Cash Acme thermostatic mixers can also be used to blend the flow and return in underfloor hydronic and radiant floor heating systems. They provide a safe, energy efficient and stable temperature in the heating system, preventing heat damage to the building and creating safer underfloor surfaces.

Series LF25AUB-Z3 lead free water pressure reducing valves are used in ... Ace Hardware / Plumbing / Valves / Pressure Regulator Valves > Compare. Watts ...

The Febco poppet bonnet assembly kit used in this demonstration contains the bonnet, poppet, and some lubricant or grease to aid in the repair process.

In most residential water heaters, temperature and pressure relief valves are designed to open when pressure reaches 150 PSI and temperature reaches 210 ...

Cash Acme is an experienced supplier of thermostatic mixing valves (TMVs), providing an extensive range of devices for residential, commercial, industrial and even hydronic heating applications. Also commonly referred to as anti-scalding valves, our TMVs accurately control the temperature of hot water at the source of heat (water heater) to deliver point-of-use (showers, sinks, lavatories, bath tubs, etc.) water at safe, controlled temperatures, regulate water distribution and flow and provide sanitary anti-scald protection.