Watts Water Technologies is a developer and manufacturer of water technologies, systems, and solutions. North Andover, Massachusetts, United States · 5001 ...

Because the reduced pressure zone assembly can be used on systems that distribute chemicals, underground installation requirements are particularly stringent. A drain to atmosphere is usually required and should be provided. This means a PVC drain fitting sits at the bottom of the valve enclosure and is connected to a drain line with adequate fall (slope) to drain any accumulation of water away from the valve enclosure to an area above ground with continuous gravity flow (cannot be drained into a pit with a rim higher than twelve inches below the reduced pressure zone assembly). The drainage trench should be dug in accordance with the irrigation site plan before the assembly is installed. Typically, a reduced pressure zone assembly enclosure can be either a job-built concrete vault or two twelve-inch deep valve boxes stacked vertically with bottoms together. When using valve boxes, the lid of the bottom box is discarded. A hole at least twenty-six inches deep and three inches larger at the bottom than the dimensions of the top of a box is filled with enough drain rock to set the bottom of the lower valve box on a flat, stable surface twenty-four inches below grade. A PVC drain fitting would be glued into a 1-1/2” sanitary street quarter bend and set with the top of the drain resting on the surface of the rock. A drain line connected to the quarter bend slopes downward to above-ground atmosphere. Landscaping mesh covers the bottom of the hole before the bottom valve box is set in place. Since an installation depth of at least twelve inches is required, the reduced pressure zone assembly is installed inline between the holes in the bottom valve box. Otherwise, the steps for connecting the reduced pressure zone assembly inline are the same as for connecting a double check valve assembly inline as explained above.

15 votes, 47 comments. 379K subscribers in the Plumbing community. A place for plumbing advice and help. Do not advertise or try to compare ...

Steps to install a reduced pressure zone assembly in an above-ground configuration are the same as for installing a double check valve assembly above ground, either indoors or outdoors, as explained above. When installed indoors, a drain must be provided for the relief valve. Steps to install a reduced pressure zone assembly in an “n” configuration are the same as for installing a double check valve assembly above ground outdoors except that it isn't necessary to install the two top elbows or unions as these come built into the assembly.

Dual Check Valves are designed to prevent cross connection of non-potable water into safe drinking water systems. Protects against back pressure and back ...

As part of the annual winterization and maintenance of the irrigation system valves, if the assembly is installed underground, clear any debris from the assembly enclosure. Open the hose bibb inside the valve box and check the end of the drain line to be sure the drain is flowing freely. Once the isolation valve has been closed and lines have been blown out, open all the valves on the reduced pressure zone assembly halfway. If the assembly is installed in an interior space, check the drain line for obstructions and ascertain that the assembly is still readily accessible. Have the assembly tested and inspected annually in accordance with local code. Scheduling an inspection just before reactivating the system in the spring will get the season off to a good start. Every five years, replace all non-metallic internal parts.

Sid Harvey's operates a network of branches from Maine to South Carolina on the East Coast, moving west throughout the Midwest to the Rocky Mountain region.

The tekmar 519 Radiant Thermostat has a built-in temperature sensor for evaluating and managing the air temperature of your room. It includes a 079 Slab Sensor, ...

JavaScript seems to be disabled in your browser. For the best experience on our site, be sure to turn on Javascript in your browser.

Each reduced pressure zone assembly comes with explicit instructions for maintenance and repair. Rubber components, check modules, and seals can be replaced by a mechanically competent homeowner or plumber. Any time the access cover is opened for any reason or the assembly is disconnected from the system, inspection and testing by a state-certified backflow assembly inspector may be required before the device is put back into service. Replacing the entire reduced pressure zone assembly with a new one is a fairly simple process. Disconnect the assembly section at the unions, and duplicate the section using a new reduced pressure zone assembly, pipe, and fittings. Then reconnect, test for leaks, and call for inspection. If the reduced pressure zone assembly is underground, make sure underground installation is still allowed under local codes.

Temperature and pressure relief valve. For domestic water system, to protect the hot water storage.

For removing air from heating systems. The air separator ensures reliable operation, better and faster heat transfer and thus contributes to reduced fuel ...

007M2QT-3/4" (vertical up). 007M2QT-1 1/4" (hor. & vert. up). 007M2PCQT 1 1/4" (hor & vert up). 007M2QT-1 1/2",. 007M2QT-1 1/2" (vertical up). 007M2PCQT-1 1/2 ...

T&P Relief valve. Manufacturer: AO Smith. SKU: 100110714. Also know as: 99465-7, 100110714, 9005899205. Shipping calculated at

Metal; Made in USA; Accepts expanded water caused by thermal expansion; Returns water to the system when hot water is used; Prevents the relief valve from ...