Pressure Reducing Valve for RO System - Maximum 70 PSI - maximum water pressure for ro system

 2024-06-19 18:51:59

watts9094"

FEATURES Replaceable bronze seats Stainless steel internal parts No special tools required for servicing Captured spring check assemblies Fused epoxy coated & lined checks Industrial strength sensing hose Field reversible relief valve AVAILABLE MODELS Suffix: BB - with bronze body (2 1 Ú2", 3")(64, 76mm) LF - without shutoffs NRS - with non-rising stem resilient wedge gate valves OS&Y - with UL/FM resilient seated outside stem and QT - with quarter-turn, full port, resilient seated QT-FDA - with FDA approved epoxy coated ball valve shutoffs S - with non-epoxy strainer S-FDA - with FDA approved epoxy coated strainer SPECIFICATIONS For Reduced Pressure Zone Backflow Preventers A reduced pressure zone backflow preventer shall be installed at each cross-connection to prevent backsiphonage and backpres-sure backflow of hazardous materials into the potable water supply. The assembly shall consist of a pressure differential re-lief valve located in a zone between two positive seating check valves and captured springs. Backsiphonage protection shall in-clude provision to admit air directly into the reduced pressure zone via a separate channel from the water discharge channel. The assembly shall include two tightly closing shutoff valves be-fore and after the valve and test cocks. The assembly shall meet the requirements of ASSE Std. Watts Regulator Company, 815 Chestnut St., N. Andover, MA 01845. Tel: 978-688-1811; Fax: 978-689-6247.

Watts9091 1/4

Sid Harvey’s operates a network of branches from Maine to South Carolina on the East Coast, moving west throughout the Midwest to the Rocky Mountain region. The branches are supplied with more than 50,000 SKU products on a continual basis from our distribution center in Wilkes-Barre, PA. Our manufacturing plant in Andrews, SC is the source for more than 1,700 Sid Harvey brand name products, both new and re-manufactured.

American Backflow is a master parts distributor. We carry backflow repair parts and backflow preventers for Ames, Conbraco, Watts, Febco, Wilkins and more.

watts909backflow preventer 4"

Looking for ORION, 15 gal Capacity, Dilution Tank? Find it at Grainger.com®. With over one million products and 24/7 customer service we have supplies and ...

AVAILABLE MODELS Suffix: BB - with bronze body (2 1 Ú2", 3")(64, 76mm) LF - without shutoffs NRS - with non-rising stem resilient wedge gate valves OS&Y - with UL/FM resilient seated outside stem and QT - with quarter-turn, full port, resilient seated QT-FDA - with FDA approved epoxy coated ball valve shutoffs S - with non-epoxy strainer S-FDA - with FDA approved epoxy coated strainer SPECIFICATIONS For Reduced Pressure Zone Backflow Preventers A reduced pressure zone backflow preventer shall be installed at each cross-connection to prevent backsiphonage and backpres-sure backflow of hazardous materials into the potable water supply. The assembly shall consist of a pressure differential re-lief valve located in a zone between two positive seating check valves and captured springs. Backsiphonage protection shall in-clude provision to admit air directly into the reduced pressure zone via a separate channel from the water discharge channel. The assembly shall include two tightly closing shutoff valves be-fore and after the valve and test cocks. The assembly shall meet the requirements of ASSE Std. Watts Regulator Company, 815 Chestnut St., N. Andover, MA 01845. Tel: 978-688-1811; Fax: 978-689-6247.

watts9091"

Supply air temperature reset is a control scheme that allows an airside system to modulate the supply air temperature based on outside air temperature ...

A thermostatic mixing valve is a unique plumbing component that is installed at or near your water heater. The valve has inlets for both hot and cold water.

We provide smart on-demand recirculation pump controllers that turn any pump into a smart hot water recirculation pump.

PWS1HE SERIES. A water softener you can feel good about!Regenerates with only 6 lbs salt per cubic foot. This represents a 33% less salt per regeneration when ...

watts9093"

watts9092"

20191014 — The most common cause is an expansion problem. When the boiler is cold it should have 12 to 15 psi on the system. If the pressure rises when the ...

This 2 1/2 inch stainless steel reduced pressure zone assembly backflow preventer helps prevent the reverse flow of contaminated water.

This 1 inch Y pattern reduced pressure zone backflow preventer assembly is designed to prevent the reverse flow of high hazard (toxic) fluids found in the ...

SPECIFICATIONS For Reduced Pressure Zone Backflow Preventers A reduced pressure zone backflow preventer shall be installed at each cross-connection to prevent backsiphonage and backpres-sure backflow of hazardous materials into the potable water supply. The assembly shall consist of a pressure differential re-lief valve located in a zone between two positive seating check valves and captured springs. Backsiphonage protection shall in-clude provision to admit air directly into the reduced pressure zone via a separate channel from the water discharge channel. The assembly shall include two tightly closing shutoff valves be-fore and after the valve and test cocks. The assembly shall meet the requirements of ASSE Std. Watts Regulator Company, 815 Chestnut St., N. Andover, MA 01845. Tel: 978-688-1811; Fax: 978-689-6247.

News