Rainwater harvesting is the collection, filtration, storage and use of rainwater from a building's roof, this collected rainwater can then be used for irrigation, horticultural, agricultural, and garden use.

#-

Above groundBackflow Enclosure

#S) and solid with insulation (

Fabricated of A366 Sht. 16 ga. with powder coat finish in green, beige, or black.  Other colors are available upon request.

HeatedBackflow Enclosure

#S/SS) or Solid Stainless Steel with insulation (

Fabricated of A366 Sht. 16 ga. with powder coat finish in green, beige, or black.  Other colors are available upon request.

#/SS). Also available, 1 1/2" Stainless Steel angle which has a sharpe edge and a greater expense (

Safe-T-Cover

The design of the Lift-off Backflow Preventer Enclosure allows for more latitude in installation. It can be mounted to existing concrete or any other hard service. This feature is very desirable when there is a need to protect existing equipment. In addition, since one size Lift-Off can cover several different sizes of valves or equipment, a Lift-Off can cost less than a standard enclosure. The Lift-Off - like all other Le Meur Enclosures - can be used for a variety of applications.

Standard hardware is intended to be embedded into concrete. Surface Mount Hardware is intended to be anchored into existing concrete. Bolts for all Models are 18-8 or Type 304 Stainless Steel

Insulated Enclosure with Two Position Hardware – this enclosure features special hardware which allows the enclosure’s gasket to seat directly on the concrete for a near perfect seal.

Solid with Insulation Added Enclosures in either carbon or stainless steel are available.  Our solid enclosure is insulated with 1” of polystyrene foam insulation with thermal conductivity of  0.25 BTUs @ 75 deg. F per inch of insulation.   Insulated enclosures are a good choice for cold climates and they also aid in sound deadening.  Our Insulated Enclosures can be ordered as follows in all sizes shown below.

All enclosures are available in Stainless Steel. Standard Stainless Steel have a rounded corner made from 12 gauge Type 304 sheeting with a directional finish on the frame (

Guardian enclosures

Backflow enclosureinstallation

Le Meur offers an EMBEDDED HARDWARE UNIT (EHU) to aid in the installation of its Backflow Enclosures. With this device a backflow can be installed with precision in minutes.

#/SS).

#-

#SI/SS).

#-

Solid with Insulation Added Enclosures in either carbon or stainless steel are available.  Our solid enclosure is insulated with 1” of polystyrene foam insulation with thermal conductivity of  0.25 BTUs @ 75 deg. F per inch of insulation.   Insulated enclosures are a good choice for cold climates and they also aid in sound deadening.  Our Insulated Enclosures can be ordered as follows in all sizes shown below.

#-

RPZenclosure

#SI). Solid Stainless Steel model number would be (

Hot Box fiberglass Enclosures

Fabricated of bar size A36 angle 1 ½” x 1 ½” x 3/16 and A366 sht.1 ½” #9 FLT expanded metal with powder coat finish in green, beige, or black.  Other colors are available upon request.

Fabricated A240 Type 304 stainless steel with a directional finish on the frame and a 2b mill finish on the expanded metal.  The expanded metal openings are deburred to protect inquisitive fingers.

Installed Height - 0", Sits on top of Concrete:We recommend allowing at least 1” clearance on each side & each end to avoid damaging the finish when removing. Height requires less clearance.

Commercial Rainwater Harvesting Tanks & Systems from The Tank Shop. These Commercial Grade Plastic and Galvanised Steel Rainwater Tanks come with options for Filters, Pumps, Hoses and taps as required. Our Commercial Rainwater Collecting Tanks range start at 10,000 litres and go up to 1.2 Million Litres in Rainwater Storage Capacities.

Insulated Enclosure with Two Position Hardware – this enclosure features special hardware which allows the enclosure’s gasket to seat directly on the concrete for a near perfect seal.

Fabricated with 1 1/4” schedule 80 steel pipe and A366 sht.1 ½” #9 FLT expanded metal with powder coat finish in green, beige, black or new LeMeur silver powder coat. Other colors are available upon request.

Fabricated A240 Type 304 stainless steel with a directional finish on the frame and a 2b mill finish on the expanded metal. The expanded metal openings are deburred to protect inquisitive fingers.

#-

InsulatedBackflow Enclosure

All enclosures are available in solid (

Solid enclosures are nice when you do not want people to see what you are covering and can be insulated for colder weather.

#X-

Lift-off enclosures work well in tight areas.  They are locked on two sides and when unlocked, lift directly off the device.

The Tank Shop Ltd have over 20 years experience selling tanks online and have built a reputation for value, honest advice and first class customer service. We are proud of our track record and only work with the best manufacturers in the UK & Germany, so you can be sure everything we sell is top quality. There are many online stores around but The Tank Shop is the best reseller.