Also consider the nature of the fluid being pumped and the material that the piping is made from. Corrosive fluids such as acids, and abrasive fluids such as slurries, will tend to be more aggressive toward the piping at higher velocities. Higher velocities will also create greater water hammer if valves are suddenly closed. If the fluid carries large particles, such as sand, the velocity should exceed the settling rate of the particles (typically about 1 m/s).

Water velocity in a pipeformula

RULES of thumb are sometimes misleading. Engineers often discuss rules of thumb for pipe sizing. Velocity (1–4 m/s) and Reynolds number (>10,000) are cited, as are pressure drop (20-80 kPa/100 m) and shear stress (>5 Pa).

We can also hook you up with a professional tradie to help you design your build and install all the valves and pipework with you.

Water velocity in pipeChart

A conversation with the experts: watch the recordings of our previous webinars and sign-up to attend future online webcasts.

Pharmaceutical engineers often cite “turbulence” as the driving criteria for sizing the piping for high purity water. The idea is that turbulent flow, defined as Reynolds number >4,000 (or >10,000, depending upon which engineer is speaking), greatly reduces the propensity for a biofilm to establish on a pipe wall. However, there is always a laminar layer at the pipe wall; it is many times deeper than a typical biofilm thickness even at a Reynolds number of 50,000. Studies show that microbes will tightly adhere to stainless steel pipe walls when the shear stress is less than 8-10 Pa. As seen on the charts, the Reynolds number needs to be well over 50,000 to achieve 10 Pa shear stress at the wall.

Discover brands such as Tomson, RMC P&T, Wilkins, and more. The best names in plumbing equipment and valve technology are here, in Reece, for you.

I made these to help me visualise the relationships between flow rate and pipe size. From these charts you can see that the “rules” are not consistent. For example, if you hold velocity constant at 2 m/s, the pressure drop varies from about 10 kPa/100 m for 12-inch pipe to >125 kPa/100 m for 1-inch.

Use the rules of thumb judiciously. Let them give you a first estimate, and use them again to reality check your final selections. Pipe sizing exercises are filled with calculations, but the formulas used in those calculations are themselves based upon empirical data and sometimes fuzzy data. These notions make the whole sizing process an engineering art form, which gives my creative side great joy.

Before applying a generalisation that you read on the internet or given by a colleague, take the time to understand the derivation for that rule of thumb and ensure it applies to your situation

One approach is to perform a life-cycle cost analysis that balances operating and maintenance costs against the initial capital investment. This analysis usually results in a velocity around 2-3 m/s, giving that rule of thumb. More expensive piping materials and larger pipe sizes tend to favour sizing for higher velocities whereas common materials and smaller sizes indicate lower velocities.

Recommendedwater velocity in pipe

You do not have to be a chemical engineer to join IChemE. Our global membership community includes people from a range of disciplines who have an interest in and/or relevant experience in chemical engineering.

2023227 — Environmental Protection Department,content page,highlights,events and activities,press releases.

A rule of thumb that incorporates pipe size is to choose liquid lines to handle a velocity of 1.5 +d/10 where “d” is the pipe diameter, inches. This gives 1.6 m/s for 1-inch and 2.5 m/s for 10-inch piping, and about 20 kPa/100 m pressure drop. Similarly, gas lines can be sized for 20d m/s and steam lines 35 m/s (maximum).

PTRs are used in both commercial and residential hot water tanks to give automatic pressure and temperature protection to hot water supply tanks and heaters.

Water velocityformula

The lesson is that general sizing rules must be tempered with good engineering. Before applying a generalisation that you read on the internet or given by a colleague, take the time to understand the derivation for that rule of thumb and ensure it applies to your situation. Pipe sizing isn’t an exact science and rules of thumb are perfectly acceptable when choosing a size, but this should be done with eyes open.

A pressure relief valve, or PTR, relieves the increase of pressure due to water expanding during the heating cycle. It does this by releasing drips of hot water to the drain line.

Series Dead Level D Pre-Sloped Trench Drain System with 6 in.(152mm) wide x 48 in.(1219mm) long (standard) ductile iron frame, UV stabilized talc-filled ...

The pipe size choice may be influenced by other factors: 1) Pipes are typically one size larger on the suction side of a pump than on the discharge; 2) a smaller-than-expected size might be selected to make installation in tight quarters easier; 3) when a very small line, such as ½” or ¾”, is acceptable, the engineer might upsize it to 1” or even 2” to provide strength, so someone who steps on the line won’t break it; and 4) short pipelines will be smaller diameter than long ones with equal pressure drops.

Shop for Shut-Off Valve at Tractor Supply Co. Buy online, free in-store pickup. Shop today!

Given a flow rate and pipe size, these charts give a Reynolds number and velocity. The charts trace any one parameter along with pipe size and yield the remaining flow parameters.

This is the fifth in a series that provides practical insights into on-the-job problems. To read more, visit the series hub at https://www.thechemicalengineer.com/tags/rules-of-thumb

Water velocityCalculator

PTRs are an integral part of all major hot waterworks. So too are thermostatic mixing valves, our expansion control valves, and our dual check valves.

Calculatevelocity in pipefrom pressure

How do you determine the pipe sizes for a system? The first step is establishing the process requirements: flow rates, fluid properties, and pipeline configuration. Many engineers then apply a rule of thumb that says to use a velocity of 1.5 to4 m/s. Higher velocities mean higher pumping cost and possibly damage to the piping due to erosion or water hammer. Lower velocities mean larger (more expensive) piping and possibly problems from fouling or solids depositions in the pipes due to insufficient turbulence.

2020228 — A hot-water recirculation system delivers hot water to a faucet, shower or appliance in seconds, eliminating the usual water-wasting wait.

Maximumvelocity in pipeformula

Genesis Water Technologies is a global leader of innovative water treatment & wastewater treatment technology serving industry, municipalities.

A compact portable device made for testing all reduced pressure zone backflow prevention assemblies, double check valve assemblies, pressure vacuum breakers.

Another sizing approach is based upon existing infrastructure limitations. For example, your plant’s chilled water pressure or a pump’s capabilities might limit the maximum pressure drop. However, you might not be able to provide a target of, for example, 60 kPa/100 m. Instead, the pipe sizing might simply be based on the available pressure drop regardless of how that fits into the generality.

Pipe length must include additional length for all fittings. Add approxi- mately 5 feet of pipe per fitting. Natural Gas Example: A burner that requires ...

Have a chat with our knowledgeable staff before you start any hot water plumbing job. Make sure you have the right tools and the right equipment so that you can make the job the best job the first time.

Water velocity in pipeCalculator

This backflow preventer has a bronze body with a wye pattern and short lay length for easy installation. It also features replaceable Noryl seats and silicone ...

Upgrade your kitchen with the Zulay 3-Piece Stainless Steel Strainer Set, designed to handle all your straining and sifting needs. Made from premium BPA-free ...

Catch up on the latest news, views and jobs from The Chemical Engineer. Below are the four latest issues. View a wider selection of the archive from within the Magazine section of this site.

WATTS 1 LFMMVM1-THREADED THERMO MIXING VALVE · 0.5 TO 20 GPM FLOW RATE · 1 INCH X 1 INCH NOMINAL SIZE · 80 TO 120 DEG F TEMPERATURE RATING · COPPER SILICON ALLOY ...