Where are RPZ valves required

The Relief Valve is operating properly, but the #1 Check Valve is not, due to the debris or damage preventing the full closure of the Check.  Depending on the amount of debris or damage, the Relief Valve can discharge just a slight drip or can open fully, flowing water until the shut-off valves are closed.

#1 = Number One Check Valve, spring-loaded up to 10 psi.#2 = Number Two Check Valve is loaded to less than 2 psi. RV = The Relief Valve operates by sensing the pressure difference across the #1 Check Valve. The Relief Valve must begin to open before the pressure difference falls below 2.0 psi.

RPZBackflow preventerdiagram

3/4 rpzbackflow preventer

The system has returned to a zero demand condition (no valves open downstream). However, debris between the #1 Check Valve seat and sealing disc, or damage in the components, is preventing the #1 Check from closing all the way. This allows pressure to equalize between the Supply Side and the Zone of Reduced Pressure. When this happens, the Relief Valve Spring pushes back against the Relief Valve Diaphram, opening the RV Discharge.

RPZ valve how it works

Deze site maakt gebruik van cookies, zodat wij je de best mogelijke gebruikerservaring kunnen bieden. Cookie-informatie wordt opgeslagen in je browser en voert functies uit zoals het herkennen wanneer je terugkeert naar onze site en helpt ons team om te begrijpen welke delen van de site je het meest interessant en nuttig vindt.

The choice between these recirculation pumps depends on the required capacity (head in relation to flow rate). Depending on the technological process requirements, the Entec recirculation pumps can be used continuously or intermittently. Other types of feed-through pumps often run continuously.

A normal centrifugal pump would require a much higher installed power for this and also requires special structural provisions that are not necessary with recirculation pumps.

If you disable this cookie, we will not be able to save your preferences. This means that every time you visit this website you will need to enable or disable cookies again.

Difference between RPZ andbackflow preventer

When the end user opens a valve (faucet, sprinkler, etc), water flows in the normal direction from the supplier, downstream to fill the user's need.  The flow of water pushes the spring-loaded check valves open. The tension of the #1 check spring maintainins the pressure difference in the Zone of Reduced Pressure. This difference in pressure keeps the relief valve in the closed position while water flows in the normal direction.

A reduction in supply side pressure caused by an incident such as a water main break, or a heavy water demand from activities such as fire fighting, causes the supply pressure to drop below the customer side pressure. A fouled #2 Check Valve allows the excess customer side pressure to act on the Relief Valve Diaphram, opening the Relief Valve discharge.  Water will discharge until the supply side pressure again exceeds the customer side pressure and closes the Relief Valve or until the shut-off valves are closed.

Recirculation pumps move a large volume of liquid at a relatively low head. The recirculation pumps are used, for example, when a liquid has to be pumped from one basin into the other basin. This is the case, for example, when waste water is pumped into sewage treatment plants from the nitrification tank to the denitrification tank.

Reduced Pressure Backflow preventerTest Procedure

Dark Blue = Supply-side pressure (for example, 100 psi) pushes against the #1 check and also fills the area on the "high pressure" side of the Relief Valve diaphram, pressing it closed.Light Blue = Reduced Pressure Zone - supply pressure pushes open the #1 check and is reduced by the #1 Check spring (for example, to 90 psi). This pressure difference across the #1 check valve maintains the relief valve in the closed position. If pressure in the Zone rises toward the supply pressure (within 2 to 3 psi), the Relief Valve discharges, preventing backflow (reverse movement of fluid).Grey = End-User Pressure - water pushes past the #2 check valve into the system of the end user.  The #2 Check prevents backflow caused by pressure increases in the down stream plumbing.

RPZ meaning

Backflow preventers are designed to stop the reverse flow of water in a plumbing system. Water suppliers often require their customers to install and maintain backflow prevention assemblies at each water meter to protect the supplier's distribution system from contamination and polution.The style most commonly required for this purpose is called a "Reduced Pressure Principal" (RPP) backflow preventer. Also known as "Reduced Pressure Zone" (RPZ), this type is preferred because it employs 3 elements of protection: the two spring loaded check valves prevent reversal of flow; the relief valve operates to discharge water prior to reversal of flow. Designed in this way, it can protect the distribution system from health hazards as well as mere polution, whether the flow reversal is due to backpressure or backsiphonage.

Debris has become lodged between the #2 check seat and sealing disc or the components are damaged.  Some source of pressure increase in the water user's system (pump, elevation, heat, etc.) is overcoming the pressure delivered by the water supplier. Because of the debris or damage fouling the #2 check, the pressure in the Zone falls to the Relief Valve Opening Point. The Relief Valve will discharge until the supply pressure again exceeds the Zone pressure or the shut-off valves are closed.

The following diagrams are artist's renderings of a Wilkins Model 975XL2. It is shown in various conditions of operation to illustrate how the RPP backflow assembly offers protection against health hazards.

The recirculation pumps are mainly used in situations where normal pumps fail because of the high dry matter content. The recirculation pumps have a large capacity, coupled with a low installed capacity and are clog-free. Very efficient!

On wastewater treatment plants, this type of transit pump is mounted in a pipe or a wall passage between two tanks to remove nitrogen and phosphate. If the water level on the discharge side is higher than on the suction side, a non-return valve must be fitted to prevent backflow. This can be part of the delivery.