Hose tap vacuum breakers are small inexpensive devices with hose connections which are simply attached to taps wherever there is a possibility of a hose being attached which could be introduced to a contaminant. However, like the atmospheric vacuum breaker they should not be used under continuous pressure.

watts 3/4pressure reducing valverepair kit

Ironically, the ordinary garden hose is the most common offender as it can be easily connected to the potable water supply and used for a variety of potentially dangerous applications.

watts 3/4pressure reducing valvehome depot

WARNING: California ResidentsThis product and/or packaging can expose you to chemicals including Styrene, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

They may be used where the degree of hazard is low, meaning the non-potable source is polluted rather than contaminated.

watts25aub3/4

Absolutely not! If there is an increase in the downstream pressure over that of the supply pressure, the check valve would tend to "modulate" thus permitting the backflow of contaminated water to pass through the orifice into the potable water supply line.

Pressure vacuum breakers may be used as protection for connections to all types of non-potable systems where the vacuum breakers are not subject to back pressure. these units may be used under continuous supply pressure. They must be installed above the usage point. (Spill resistant models for indoor use are also available).

Back siphonage is the reversal of normal flow in a system caused by a negative pressure (vacuum or partial vacuum) in the supply piping.

Sustainable Supply has been focusing on our customers and their work since 2009. It’s why we carry over 1,000,000 products and built a website dedicated to your ordering experience. We’re in the business of helping you save time, save money, get your product quickly, and be as green as you want to be.

ZurnPressure Reducing Valve

Pressure Reducing Valve

Backpressure backflow is the reversal of normal flow in a system due to an increase in the downstream pressure above that of the supply pressure.

Back siphonage can be created when there is a stoppage of the water supply due to nearby fire-fighting, repairs or breaks in city main, etc. The effect is similar to the sipping of a drink through a straw, which induces a flow in the opposite direction.

Fire protection systems are most commonly constructed of uncoated black iron pipe which is considered by plumbing officials to be unacceptable as water system piping material.

This term is applied to an installation in which the pressure is being supplied continuously to a backflow preventer for periods of over 12 hours at a time. Laboratory faucet equipment, for example, is entirely suitable for a non-pressure, atmospheric anti-siphon vacuum breaker because the supply is periodically being turned on and shut off. A vacuum breaker should never be subjected to continuous pressure unless it is of the continuous pressure type and clearly identified for this service.

WattsPressure Reducing ValveManual

Atmospheric vacuum breakers may be used only on connections to a non-potable system where the vacuum breaker is never subjected to back pressure, and is installed on the discharge side of the last control valve. It must be installed above the usage point. It cannot be used under continuous pressure. (Also see #7)

Back pressure backflow is created whenever the downstream pressure exceeds the supply pressure which is possible in installations such as heating systems, elevated tanks, and pressure producing systems. An example would be a space-heating boiler operating under 103 to 138 kPa coincidental with a reduction of the city water supply below such pressure (or higher in most commercial boilers). As water tends to flow in the direction of least resistance, a back pressure backflow condition would be created and the contaminated boiler water would flow into the potable water supply.

The most commonly used atmospheric anti-siphon vacuum breakers incorporate an atmospheric vent in combination with a check valve. Its operation depends on a supply of potable water to seal off the atmospheric vent, admitting the water to downstream equipment. If a negative pressure develops in the supply line, the loss of pressure permits the check valve to drop sealing the orifice while at the same time the vent opens admitting air to the system to break the vacuum.

A cross-connection is a direct arrangement of a piping line which allows the potable water supply to be connected to a line which contains a contaminant. An example is the common garden hose attached to a tap with the end of the hose lying in a pool of muddy water. Another example would be a garden hose attached to a tap with the end of the hose submerged in a tub full of detergent.

They can be used anywhere you need to protect direct connections from foreign material that might enter the potable system in concentration which does not constitute a health hazard.