ManifoldMarkets

The IADC Lexicon is © IADC. However, the documents from which the definitions were drawn may be copyrighted by the original sources, and may not be used without express permission of the copyright holders. IADC expressly recognizes the copyrights of contributors to this Lexicon, including API, OGP, ISO, NORSOK and DNV.

ManifoldPipe

28 Sept 2022 — Radiant heat is an ingenious way to improve your quality of life while warming your space efficiently.

ManifoldMathematics

Manifolds can be used to gather produced fluids and direct selected wells to a well test line, as well as to distribute injected fluids (gas or water) or gaslift gas to individual wells. An alternative to the use of individual valves on each branch line is the use of a multiport selector which can be remotely switched to direct a desired well into a test line for instance, while leaving all other wells flowing into the main production line.

Source: API STD 521, Pressure-relieving and Depressuring Systems, Fifth Edition, January 2007 (Addendum May 2008). Global Standards

KF-1076. S&B Intake Replacement Filter. Filter Type. Cotton Cleanable Dry Extendable. $69.00 USD. KF-1073.

Manifoldbetting

As they warm the water, the water will undergo thermal expansion, meaning it will become pressurized inside of the tank. The T&P valve is a safety mechanism ...

ManifoldSatisfactory

LP Gas Tank Regulator Installation ... All ASME propane tanks in service are required to have a regulator installed no more than 36 inches from the tank's service ...

A system of pipe and valves that serves to convert separate flows into one flow, to divide one flow into separate parts, or to re route a flow to any one of several possible destinations.

Find the Right Water Filter System for You. Are you looking for a drinking or whole of house filtration setup? Browse below and explore our extensive range of ...

A manifold is a system of headers and branched piping that can be used to gather or distribute fluids, as desired. Typically manifolds include valves for controlling the on/off flow of fluids, and may also include other flow control devices (e.g. chokes) if these are not mounted on the individual subsea trees.

ManifoldEngineering

If you would like to be notified when we answer your question please log in or enter your email below. If not please leave the email blank and press submit thank you.

Differential Gauges - Backflow Test Kits and Hoses Differential Gauges.

The 825Y Reduced Pressure Zone assemblies protect against high hazard fluids, learn more about this backflow device.

Source: API RP 17A, Design and Operation of Subsea Production Systems—General Requirements and Recommendations, Fourth Edition, Reaffirmed 2011. Global Standards

Need help using the IADC Lexicon? The FAQ section will answer most of your questions, and you can also submit questions directly.

Source: API SPEC 16D, Specification for Control Systems for Drilling Well Control Equipment and Control Systems for Diverter Equipment, Upstream Segment, Second Edition, July 2004. Global Standards

An assemblage of pipe, valves, and fittings by which fluid from one or more sources is selectively directed to various systems or components.

Manifoldon a car

F1100-C-EF Round Funnel Floor Drain with cast iron membrane clamp ring with primary and secondary weep holes for waterproofing, more.

2020312 — Backflow preventers ensure that water in a home or business boiler system does not flow into the drinking water. The water in your pipes is only ...

Manifoldvalve

Additionally, for automotive market, suppliers must achieve IATF 16949 certification OR meet the Minimum. Automotive Quality Management System Requirements ( ...

Manifold(s) include connection points for tie-in of the flowline(s) and/or umbilical back to the host facility, as well as connection points for the individual production wells. Manifolds require some type of framework to provide structural support of the various piping and valves, etc. Sometimes this framework and the manifold are incorporated into the towhead of a pipeline bundle, in which case this is commonly referred to as a PLEM. Alternatively, a separately installed template may be provided to support the manifold as described below.

Source: API RP 17A, Design and Operation of Subsea Production Systems—General Requirements and Recommendations, Fourth Edition, Reaffirmed 2011. Global Standards

Source: API RP 13C, Recommended Practice on Drilling Fluids Processing Systems Evaluation, Upstream Segment, Fourth Edition, December 2010. Global Standards