Shut off valves are designed to safely stop the flow of hazardous fluids or gases. It also regulates compressed air in industrial automation processes when not ...

Febco825Y RP

No, drip tube isn’t simply holes punched into poly pipe. Inside each hole is an intricate dripper which delivers that water nice and evenly. Punching a hole will simply create an uncontrolled leak!

Febco825YA

1 Aug 2008 — Adjusting the breathing resistance knob on a regulator simply adjust the amount of effort necessary to begin the flow of air from the regulator.

Febco860

The main cause of blowout is pressure. Whether it’s poly fittings, PVC fittings or timers, whatever the component, if the pressure is too high for what it’s designed for, kaboom! Simply solve the problem with a pressure reducer & make it a brass one if it’s on your water supply.

Luckily the replacement unit was the same length as the old 2 to 1 reducer. So replacement was effected in 15 minutes. The new 500kPa pressure reducer exhibits a higher flow rate characteristic relative to the replaced unit. Supply and postage was prompt.

Zurn Wilkins 975XL2 REDUCED PRESSURE PRINCIPLE BACKFLOW PREVENTER features a wye pattern bronze body with separate access to each check and relief valve for ...

Watts Regulator Backflow Preventer 9D Vacuum Breaker 1/2 Inch Bronze Threaded 9DM3-12T-IN STOCK.

Be prepared with the most accurate 10-day forecast for Saint Pauls, NC with highs, lows, chance of precipitation from The Weather Channel and Weather.com.

These brass fixed pressure regulating valves are ideal for systems which require reduced & regulated pressure, like drip irrigation systems. For areas with high pressure.

Plastic pressure reducers can’t handle constant high pressure so the benefit with a brass pressure regulator is that you can put one on at the water connection for a drip irrigation system rather than one plastic pressure reducer on each zone.

Febco850

With Irrigation, Garden Lighting, Pond Pumps & Filtration, Pressure Pumps & Water Tanks, Turf & More available to buy online at our store, SunshowerOnline is the place to go to bring your garden to life! Located in the South East suburbs of Melbourne, Victoria, we have decades of experience to give you the information and advice you need to make your garden award worthy! Have a browse through our Product Categories, Shop by Brand, check out our great Specials, get handy advice from our Help Centre & Blog, then buy online with just a few clicks!

Each sprinkler & nozzle will push out water at different rates, but the key factor is the flow rate of your water supply. Work that out with a simple timed bucket test. From there, you can work out how much water each sprinkler you’re looking at uses & work within your flow limit. For more information, check our Product Guides.

Plastic pressure reducers can’t handle constant high pressure so the benefit with a brass pressure regulator is that you can put one on at the water connection for a drip irrigation system rather than one plastic pressure reducer on each zone.

As you install a system, it’s almost inevitable that small fragments of dirt will get into the pipe, for this reason you should always flush out the system before running it the first time. This can be done by leaving an open end at the farthest point of each irrigation zone & operating the zone for 15 or so seconds to flush it out. Then plug it up & you’re good to go! This can also be said for any other times dirt may have gotten into the system (eg: further irrigation repairs or a mains water supply fault).

We definitely don’t recommend it. Typically, drip tube will deliver the water at a far slower rate that sprays. Because of this, if you were to have both on the same zone, the areas with drip would be left far drier than the areas with sprinkler coverage. If you do want to water some areas with drip & some with sprinklers, it can be done, but each will just need to be run on their own separate irrigation zones.

Febco825Y test ports

We also had the wonderful opportunity to co-host the Boston Bluegrass Union showcase room with another fantastic act, Rock Hearts I couldn't be more grateful to ...

There’s no best type of sprinkler, just better sprinklers for different applications. Gear Drives are better for large areas, over 5m. Pop-Ups are ideal for 1.5-5m & Micro sprays are excellent for anything under that.

Febco825Y test procedures

FEBCO825Y spec Sheet

Maintenance Repair Kits & Parts · Faucets · All Faucets · Specialty Faucets · Bedpan ... This Watts HY-420-6 Non-Freeze Wall Hydrant is manufactured by Watts.

This 1/2 inch dual check valve backflow preventer with atmospheric vent helps prevent the reverse flow of hot or cold polluted water from entering into the ...

Need more help with Pressure Reducers & Filters, Pressure Regulating Valves ? Check out these handy resources from our Help Centre

Protect a client's clean water source from contaminated backflow by installing an anti-siphon valve. Order online and pick it up at your nearest SiteOne ...

Febco825Y Repair Kit

These brass fixed pressure regulating valves are ideal for systems which require reduced & regulated pressure, like drip irrigation systems. For areas with high pressure.

Warmzone offers the most advanced hydronic floor heating components, including industry-leading lightweight panels with PEX tubing.

Drip tube is excellent in areas of rich dense soil where water spreads nicely throughout. Installed under mulch, the water is delivered with minimal evaporation & wastage, going direct to the root ball.

Even on a typical domestic system running on mains water a filter is still a good idea. In the event of a water main fault where rubbish does find it’s way down the line, a filter will protect the system from blockage and or failure. On systems operating off recycled water, like from a tank, a screen filter is mandatory. Debris like silt & dirt from recycled water is the most common cause of blockages of failures in irrigation systems.