These instructions cover the most common set up configurations. If you ordered different colored tubing or filter cartridge housings, you may not be able to follow these instructions completely. Please contact us if you have problems with your unit. Customer is responsible for filter and membrane changes and associated costs. We carry a complete line of parts and accessories for all of our systems. Thank you for your business!

Our Commercial Hydroponic System is a customized Reverse Osmosis water filter that is capable of reducing up to 99% of most contaminants. This system is designed for use with hydroponic or horticultural applications. This system is built to give the maximum amount of flow from the membrane while sending less waste water to the drain, compared to similar RO filters. Please read the following setup and maintenance guide to get the maximum results from your filter.

Bad MembraneReplace Membrane and sanitize when below 75% rejectionWater Supply has a high oxygen contentSystem is still newWater does not taste or smell rightBad Membrane – Replace membrane when 75% rejection and sanitizeFilters have expired – Replace filters.©Should replace every 6 to 12 months.System needs sanitizingLow Water OutputIncoming water pressure is below 40 PSI,Increase pressure to 40 psiBad check valve, Replace check valve, Open valve.Filters clogged Replace filtersKinked tube Unkink tube If damaged, replace tubeDocuments / ResourcesPREMIER WATER SYSTEMS 1000 GPD Commercial RO Reverse Osmosis Water Filter System [pdf] Owner's ManualCBBREP32520K85, 600 GPD, 1000 GPD, Commercial RO Reverse Osmosis Water Filter SystemReferences Premier Water Systems | Whole House Water Filtration ProsUser ManualRelated PostsTastePURE Water Filter GuideTastePURE™ Water Filter Guide This is just a partial list of contaminates removed by the TastePURE™ line of…APEC Water Systems RO-QUICK90 System Filter InstructionsRO-QUICK90 System Filter Change Instruction How To Replace Stages 1, 2 Pre-Filters: Turn OFF cold water supply to…GE Shower Water Filter InstructionsGE Shower Water Filter Instruction A REPLACEMENT FOR THE FOLLOWING WATER FILTER: FXSCH FILTER USE: 6 MONTHS OR…Pelican Water Systems WF6/ WF10 Owner's ManualPelican Water Systems WF6/ WF10 Owner's Manual - Download [optimized] Pelican Water Systems WF6/ WF10 Owner's Manual -…

WattsPremierRO-TFM-5SVManual

Warning: any modifications to an appliance outside of the manufacturer’s specifications may void the appliance certification.

Congratulations on your new Premier Commercial water treatment system. We hope your system brings you many years of service and fresh clean water. There are a few basic steps we wanted to inform you about when it comes to the installation and maintenance of your water treatment system. If you should have any difficulties or questions, do not hesitate to contact us and we will be happy to help you any way we can.

Your system was built to order, and it is ready to hook up to a water supply with the appropriate adapters included. Your system has been pressure tests all systems prior to shipping, so your RO membrane will be installed. The only other work you need to complete is hooking the unit up to a supply and drain line.

Wattspremier Reverse Osmosisdiagram

Low Water OutputIncoming water pressure is below 40 PSI,Increase pressure to 40 psiBad check valve, Replace check valve, Open valve.Filters clogged Replace filtersKinked tube Unkink tube If damaged, replace tubeDocuments / ResourcesPREMIER WATER SYSTEMS 1000 GPD Commercial RO Reverse Osmosis Water Filter System [pdf] Owner's ManualCBBREP32520K85, 600 GPD, 1000 GPD, Commercial RO Reverse Osmosis Water Filter SystemReferences Premier Water Systems | Whole House Water Filtration ProsUser ManualRelated PostsTastePURE Water Filter GuideTastePURE™ Water Filter Guide This is just a partial list of contaminates removed by the TastePURE™ line of…APEC Water Systems RO-QUICK90 System Filter InstructionsRO-QUICK90 System Filter Change Instruction How To Replace Stages 1, 2 Pre-Filters: Turn OFF cold water supply to…GE Shower Water Filter InstructionsGE Shower Water Filter Instruction A REPLACEMENT FOR THE FOLLOWING WATER FILTER: FXSCH FILTER USE: 6 MONTHS OR…Pelican Water Systems WF6/ WF10 Owner's ManualPelican Water Systems WF6/ WF10 Owner's Manual - Download [optimized] Pelican Water Systems WF6/ WF10 Owner's Manual -…

A hose assembly for an appliance needs to be connected to the appliance and the consumer piping by a threaded or other metal connection. There are three allowable connection methods depending on the hose assembly setup:

A significant number of the gas applications Energy Safe Victoria receives are for commercial kitchen installations, and a major reason for failed commercial kitchen inspections is the incorrect installation of appliances and hose assemblies. As a result, Energy Safe has provided gasfitters with several aides to help achieve a compliant commercial kitchen installation that include:

Commercial catering equipment connected by hose assembly must be restrained to prevent stress being applied to the hose connections when the appliance is moved, where the accepted method of restraint:

The requirements contained within AS/NZS 5601.1 clause 6.10.2.7 will form part of Energy Safe's zero tolerance strategy as of 1 April 2023.

Installation InstructionsCongratulations on your new Premier Commercial water treatment system. We hope your system brings you many years of service and fresh clean water. There are a few basic steps we wanted to inform you about when it comes to the installation and maintenance of your water treatment system. If you should have any difficulties or questions, do not hesitate to contact us and we will be happy to help you any way we can.We strongly recommend to hooking your Commercial RO unit to a softened water supply. Your system was built to order, and it is ready to hook up to a water supply with the appropriate adapters included. Your system has been pressure tests all systems prior to shipping, so your RO membrane will be installed. The only other work you need to complete is hooking the unit up to a supply and drain line.Unpack your unit completely.Inspect for any damage or broken parts as a result of shipping.Locate and connect the supply side (RIGHT SIDE of lower housing) of the equipment. The side port is ready for the supply tube, the Black 3/8” tubing.Then connect your specified adaptor, if it has not already been done.Locate and connect the Drain line to the other end of the membrane housing (LEFT SIDE). The correct port for the drain line is the port to the side, not the center port. Place the other end in an appropriate area to accept drain water.Take the remaining tube and insert it into the remaining open port (center) on the membrane housing (RIGHT SIDE). This is the product/RO water.Now allow the system to run for approximately 15 minutes to flush completely. Please check systems for leaks, parts can come lose during shipping!These instructions cover the most common set up configurations. If you ordered different colored tubing or filter cartridge housings, you may not be able to follow these instructions completely. Please contact us if you have problems with your unit. Customer is responsible for filter and membrane changes and associated costs. We carry a complete line of parts and accessories for all of our systems. Thank you for your business!PREMIER WATER SYSTEMS7623 FULTON AVE | NORTH HOLLYWOOD CA 91605(661) 575 – 0033WWW.PREMIERWATERSYSTEMS.NETCommercial Membrane Installation and Replacement GuideFeed Side of Membrane HousingInsert membrane into housing, making careful to note, which side has the brine seal. The use of a non-petroleum based lubricant is acceptable, if needed.Insert Plug into center hole on brine seal side.Thread Tefloned fitting in to Off-Center hole This will be where the Feed Water is introduced to the membraneProduct Side of Membrane HousingThread the 2 remaining fittings in the “bottom” cap.Insert tube into the off-center fitting, this will be the drain, run tubing to your drain line NOW. Then cut this line and insert the ball valve provided. See diagram above. This valve will need to be adjusted on occasion, so place in an accessible spot, but not where it will be accidentally re-adjusted. Open this valve 1/2 way for now.The Product water (good water) will come out through the center fitting, attach the tube now.Start running water through SLOWLY, turn up the volume SLOWLY, until you are at full volume, do this over a 45 to 60 second period.Run the first few gallons of the Product water to drain to clean the membrane.Then slowly adjust the valve until you have a 1 to 1 ratio of product to water**** in order to have a 1 to 1 ratio you must feed this membrane with softened water, for other hard water or any other water high in TDS you must waste at 2 parts waste to 1 part product waterREPLACEMENT FILTERS:MODEL # CBBREP32520K85WWW.PREMIERWATERSYSTEMS.NETTrouble shooting guide to assist with the determination of ProblemsTrouble Shooting GuideCloudy or milky colored water:Bad MembraneReplace Membrane and sanitize when below 75% rejectionWater Supply has a high oxygen contentSystem is still newWater does not taste or smell rightBad Membrane – Replace membrane when 75% rejection and sanitizeFilters have expired – Replace filters.©Should replace every 6 to 12 months.System needs sanitizingLow Water OutputIncoming water pressure is below 40 PSI,Increase pressure to 40 psiBad check valve, Replace check valve, Open valve.Filters clogged Replace filtersKinked tube Unkink tube If damaged, replace tubeDocuments / ResourcesPREMIER WATER SYSTEMS 1000 GPD Commercial RO Reverse Osmosis Water Filter System [pdf] Owner's ManualCBBREP32520K85, 600 GPD, 1000 GPD, Commercial RO Reverse Osmosis Water Filter SystemReferences Premier Water Systems | Whole House Water Filtration ProsUser ManualRelated PostsTastePURE Water Filter GuideTastePURE™ Water Filter Guide This is just a partial list of contaminates removed by the TastePURE™ line of…APEC Water Systems RO-QUICK90 System Filter InstructionsRO-QUICK90 System Filter Change Instruction How To Replace Stages 1, 2 Pre-Filters: Turn OFF cold water supply to…GE Shower Water Filter InstructionsGE Shower Water Filter Instruction A REPLACEMENT FOR THE FOLLOWING WATER FILTER: FXSCH FILTER USE: 6 MONTHS OR…Pelican Water Systems WF6/ WF10 Owner's ManualPelican Water Systems WF6/ WF10 Owner's Manual - Download [optimized] Pelican Water Systems WF6/ WF10 Owner's Manual -…

The currency and accuracy of this document cannot be guaranteed once printed or saved to a storage device. If in doubt, please check the ESV website for the current version.

(661) 575 – 0033WWW.PREMIERWATERSYSTEMS.NETCommercial Membrane Installation and Replacement GuideFeed Side of Membrane HousingInsert membrane into housing, making careful to note, which side has the brine seal. The use of a non-petroleum based lubricant is acceptable, if needed.Insert Plug into center hole on brine seal side.Thread Tefloned fitting in to Off-Center hole This will be where the Feed Water is introduced to the membraneProduct Side of Membrane HousingThread the 2 remaining fittings in the “bottom” cap.Insert tube into the off-center fitting, this will be the drain, run tubing to your drain line NOW. Then cut this line and insert the ball valve provided. See diagram above. This valve will need to be adjusted on occasion, so place in an accessible spot, but not where it will be accidentally re-adjusted. Open this valve 1/2 way for now.The Product water (good water) will come out through the center fitting, attach the tube now.Start running water through SLOWLY, turn up the volume SLOWLY, until you are at full volume, do this over a 45 to 60 second period.Run the first few gallons of the Product water to drain to clean the membrane.Then slowly adjust the valve until you have a 1 to 1 ratio of product to water**** in order to have a 1 to 1 ratio you must feed this membrane with softened water, for other hard water or any other water high in TDS you must waste at 2 parts waste to 1 part product waterREPLACEMENT FILTERS:MODEL # CBBREP32520K85WWW.PREMIERWATERSYSTEMS.NETTrouble shooting guide to assist with the determination of ProblemsTrouble Shooting GuideCloudy or milky colored water:Bad MembraneReplace Membrane and sanitize when below 75% rejectionWater Supply has a high oxygen contentSystem is still newWater does not taste or smell rightBad Membrane – Replace membrane when 75% rejection and sanitizeFilters have expired – Replace filters.©Should replace every 6 to 12 months.System needs sanitizingLow Water OutputIncoming water pressure is below 40 PSI,Increase pressure to 40 psiBad check valve, Replace check valve, Open valve.Filters clogged Replace filtersKinked tube Unkink tube If damaged, replace tubeDocuments / ResourcesPREMIER WATER SYSTEMS 1000 GPD Commercial RO Reverse Osmosis Water Filter System [pdf] Owner's ManualCBBREP32520K85, 600 GPD, 1000 GPD, Commercial RO Reverse Osmosis Water Filter SystemReferences Premier Water Systems | Whole House Water Filtration ProsUser ManualRelated PostsTastePURE Water Filter GuideTastePURE™ Water Filter Guide This is just a partial list of contaminates removed by the TastePURE™ line of…APEC Water Systems RO-QUICK90 System Filter InstructionsRO-QUICK90 System Filter Change Instruction How To Replace Stages 1, 2 Pre-Filters: Turn OFF cold water supply to…GE Shower Water Filter InstructionsGE Shower Water Filter Instruction A REPLACEMENT FOR THE FOLLOWING WATER FILTER: FXSCH FILTER USE: 6 MONTHS OR…Pelican Water Systems WF6/ WF10 Owner's ManualPelican Water Systems WF6/ WF10 Owner's Manual - Download [optimized] Pelican Water Systems WF6/ WF10 Owner's Manual -…

7623 FULTON AVE | NORTH HOLLYWOOD CA 91605(661) 575 – 0033WWW.PREMIERWATERSYSTEMS.NETDescriptionOur Commercial Hydroponic System is a customized Reverse Osmosis water filter that is capable of reducing up to 99% of most contaminants. This system is designed for use with hydroponic or horticultural applications. This system is built to give the maximum amount of flow from the membrane while sending less waste water to the drain, compared to similar RO filters. Please read the following setup and maintenance guide to get the maximum results from your filter.PrecautionsDo not install the unit where the source/inlet pressure may be more than 80 psi or there are excessive water hammer/spike problems. Keep out of direct sunlight or high intensity lights, which degrade the housing and fittings over time.Do not drop or place heavy objects on top of unit.Do not install where leakage or failure may cause damage to property.Operating RequirementsMinimum water pressure: 40 PSI, Maximum water pressure: 200 PSI, Optimal water temperature: 77*F (25*C), Maximum water temperature: 105*F (40.5*C) – Up to 1000 (or 600) Gallons per day at 100 PSI. At lower PSI = lower production. i.e. 70 psi 700 GPDOptional Additions (NOT INCLUDED)AUTO-SHUT OFF VALVE, DI FILTER, BOOSTER PUMPInstallation InstructionsCongratulations on your new Premier Commercial water treatment system. We hope your system brings you many years of service and fresh clean water. There are a few basic steps we wanted to inform you about when it comes to the installation and maintenance of your water treatment system. If you should have any difficulties or questions, do not hesitate to contact us and we will be happy to help you any way we can.We strongly recommend to hooking your Commercial RO unit to a softened water supply. Your system was built to order, and it is ready to hook up to a water supply with the appropriate adapters included. Your system has been pressure tests all systems prior to shipping, so your RO membrane will be installed. The only other work you need to complete is hooking the unit up to a supply and drain line.Unpack your unit completely.Inspect for any damage or broken parts as a result of shipping.Locate and connect the supply side (RIGHT SIDE of lower housing) of the equipment. The side port is ready for the supply tube, the Black 3/8” tubing.Then connect your specified adaptor, if it has not already been done.Locate and connect the Drain line to the other end of the membrane housing (LEFT SIDE). The correct port for the drain line is the port to the side, not the center port. Place the other end in an appropriate area to accept drain water.Take the remaining tube and insert it into the remaining open port (center) on the membrane housing (RIGHT SIDE). This is the product/RO water.Now allow the system to run for approximately 15 minutes to flush completely. Please check systems for leaks, parts can come lose during shipping!These instructions cover the most common set up configurations. If you ordered different colored tubing or filter cartridge housings, you may not be able to follow these instructions completely. Please contact us if you have problems with your unit. Customer is responsible for filter and membrane changes and associated costs. We carry a complete line of parts and accessories for all of our systems. Thank you for your business!PREMIER WATER SYSTEMS7623 FULTON AVE | NORTH HOLLYWOOD CA 91605(661) 575 – 0033WWW.PREMIERWATERSYSTEMS.NETCommercial Membrane Installation and Replacement GuideFeed Side of Membrane HousingInsert membrane into housing, making careful to note, which side has the brine seal. The use of a non-petroleum based lubricant is acceptable, if needed.Insert Plug into center hole on brine seal side.Thread Tefloned fitting in to Off-Center hole This will be where the Feed Water is introduced to the membraneProduct Side of Membrane HousingThread the 2 remaining fittings in the “bottom” cap.Insert tube into the off-center fitting, this will be the drain, run tubing to your drain line NOW. Then cut this line and insert the ball valve provided. See diagram above. This valve will need to be adjusted on occasion, so place in an accessible spot, but not where it will be accidentally re-adjusted. Open this valve 1/2 way for now.The Product water (good water) will come out through the center fitting, attach the tube now.Start running water through SLOWLY, turn up the volume SLOWLY, until you are at full volume, do this over a 45 to 60 second period.Run the first few gallons of the Product water to drain to clean the membrane.Then slowly adjust the valve until you have a 1 to 1 ratio of product to water**** in order to have a 1 to 1 ratio you must feed this membrane with softened water, for other hard water or any other water high in TDS you must waste at 2 parts waste to 1 part product waterREPLACEMENT FILTERS:MODEL # CBBREP32520K85WWW.PREMIERWATERSYSTEMS.NETTrouble shooting guide to assist with the determination of ProblemsTrouble Shooting GuideCloudy or milky colored water:Bad MembraneReplace Membrane and sanitize when below 75% rejectionWater Supply has a high oxygen contentSystem is still newWater does not taste or smell rightBad Membrane – Replace membrane when 75% rejection and sanitizeFilters have expired – Replace filters.©Should replace every 6 to 12 months.System needs sanitizingLow Water OutputIncoming water pressure is below 40 PSI,Increase pressure to 40 psiBad check valve, Replace check valve, Open valve.Filters clogged Replace filtersKinked tube Unkink tube If damaged, replace tubeDocuments / ResourcesPREMIER WATER SYSTEMS 1000 GPD Commercial RO Reverse Osmosis Water Filter System [pdf] Owner's ManualCBBREP32520K85, 600 GPD, 1000 GPD, Commercial RO Reverse Osmosis Water Filter SystemReferences Premier Water Systems | Whole House Water Filtration ProsUser ManualRelated PostsTastePURE Water Filter GuideTastePURE™ Water Filter Guide This is just a partial list of contaminates removed by the TastePURE™ line of…APEC Water Systems RO-QUICK90 System Filter InstructionsRO-QUICK90 System Filter Change Instruction How To Replace Stages 1, 2 Pre-Filters: Turn OFF cold water supply to…GE Shower Water Filter InstructionsGE Shower Water Filter Instruction A REPLACEMENT FOR THE FOLLOWING WATER FILTER: FXSCH FILTER USE: 6 MONTHS OR…Pelican Water Systems WF6/ WF10 Owner's ManualPelican Water Systems WF6/ WF10 Owner's Manual - Download [optimized] Pelican Water Systems WF6/ WF10 Owner's Manual -…

WattsPremierFilter replacement instructions

Installing a buffer (or spacer) behind an appliance helps prevent strain, abrasion, or kinking of the hose when the appliance is moved back into position. Given the mobility of the appliance, buffers also ensure that surrounding combustible surfaces (behind and on each side of the appliance) are protected and minimum manufacturer clearances are maintained.

Cloudy or milky colored water:Bad MembraneReplace Membrane and sanitize when below 75% rejectionWater Supply has a high oxygen contentSystem is still newWater does not taste or smell rightBad Membrane – Replace membrane when 75% rejection and sanitizeFilters have expired – Replace filters.©Should replace every 6 to 12 months.System needs sanitizingLow Water OutputIncoming water pressure is below 40 PSI,Increase pressure to 40 psiBad check valve, Replace check valve, Open valve.Filters clogged Replace filtersKinked tube Unkink tube If damaged, replace tubeDocuments / ResourcesPREMIER WATER SYSTEMS 1000 GPD Commercial RO Reverse Osmosis Water Filter System [pdf] Owner's ManualCBBREP32520K85, 600 GPD, 1000 GPD, Commercial RO Reverse Osmosis Water Filter SystemReferences Premier Water Systems | Whole House Water Filtration ProsUser ManualRelated PostsTastePURE Water Filter GuideTastePURE™ Water Filter Guide This is just a partial list of contaminates removed by the TastePURE™ line of…APEC Water Systems RO-QUICK90 System Filter InstructionsRO-QUICK90 System Filter Change Instruction How To Replace Stages 1, 2 Pre-Filters: Turn OFF cold water supply to…GE Shower Water Filter InstructionsGE Shower Water Filter Instruction A REPLACEMENT FOR THE FOLLOWING WATER FILTER: FXSCH FILTER USE: 6 MONTHS OR…Pelican Water Systems WF6/ WF10 Owner's ManualPelican Water Systems WF6/ WF10 Owner's Manual - Download [optimized] Pelican Water Systems WF6/ WF10 Owner's Manual -…

Bad Membrane – Replace membrane when 75% rejection and sanitizeFilters have expired – Replace filters.©Should replace every 6 to 12 months.System needs sanitizingLow Water OutputIncoming water pressure is below 40 PSI,Increase pressure to 40 psiBad check valve, Replace check valve, Open valve.Filters clogged Replace filtersKinked tube Unkink tube If damaged, replace tubeDocuments / ResourcesPREMIER WATER SYSTEMS 1000 GPD Commercial RO Reverse Osmosis Water Filter System [pdf] Owner's ManualCBBREP32520K85, 600 GPD, 1000 GPD, Commercial RO Reverse Osmosis Water Filter SystemReferences Premier Water Systems | Whole House Water Filtration ProsUser ManualRelated PostsTastePURE Water Filter GuideTastePURE™ Water Filter Guide This is just a partial list of contaminates removed by the TastePURE™ line of…APEC Water Systems RO-QUICK90 System Filter InstructionsRO-QUICK90 System Filter Change Instruction How To Replace Stages 1, 2 Pre-Filters: Turn OFF cold water supply to…GE Shower Water Filter InstructionsGE Shower Water Filter Instruction A REPLACEMENT FOR THE FOLLOWING WATER FILTER: FXSCH FILTER USE: 6 MONTHS OR…Pelican Water Systems WF6/ WF10 Owner's ManualPelican Water Systems WF6/ WF10 Owner's Manual - Download [optimized] Pelican Water Systems WF6/ WF10 Owner's Manual -…

Commercial catering equipment must be certified and installed in accordance with AS/NZS 5601.1 Gas Installations Part 1: General installations, but as a quick guide to a compliant installation, any appliance on castors, rollers, wheels, or that is designed to be slid out for servicing must be:

WattsPremierWP-5Manual

PremierRO Pure Plus Filters

This website is an independent publication and is neither affiliated with nor endorsed by any of the trademark owners. The "Bluetooth®" word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. The "Wi-Fi®" word mark and logos are registered trademarks owned by the Wi-Fi Alliance. Any use of these marks on this website does not imply any affiliation with or endorsement.

Trouble Shooting GuideCloudy or milky colored water:Bad MembraneReplace Membrane and sanitize when below 75% rejectionWater Supply has a high oxygen contentSystem is still newWater does not taste or smell rightBad Membrane – Replace membrane when 75% rejection and sanitizeFilters have expired – Replace filters.©Should replace every 6 to 12 months.System needs sanitizingLow Water OutputIncoming water pressure is below 40 PSI,Increase pressure to 40 psiBad check valve, Replace check valve, Open valve.Filters clogged Replace filtersKinked tube Unkink tube If damaged, replace tubeDocuments / ResourcesPREMIER WATER SYSTEMS 1000 GPD Commercial RO Reverse Osmosis Water Filter System [pdf] Owner's ManualCBBREP32520K85, 600 GPD, 1000 GPD, Commercial RO Reverse Osmosis Water Filter SystemReferences Premier Water Systems | Whole House Water Filtration ProsUser ManualRelated PostsTastePURE Water Filter GuideTastePURE™ Water Filter Guide This is just a partial list of contaminates removed by the TastePURE™ line of…APEC Water Systems RO-QUICK90 System Filter InstructionsRO-QUICK90 System Filter Change Instruction How To Replace Stages 1, 2 Pre-Filters: Turn OFF cold water supply to…GE Shower Water Filter InstructionsGE Shower Water Filter Instruction A REPLACEMENT FOR THE FOLLOWING WATER FILTER: FXSCH FILTER USE: 6 MONTHS OR…Pelican Water Systems WF6/ WF10 Owner's ManualPelican Water Systems WF6/ WF10 Owner's Manual - Download [optimized] Pelican Water Systems WF6/ WF10 Owner's Manual -…

Home » PREMIER WATER SYSTEMS » PREMIER WATER SYSTEMS 1000 GPD Commercial RO Reverse Osmosis Water Filter System Owner’s Manual

This gas information sheet provides information about installing and connecting commercial catering equipment using hose assemblies. This information sheet is to be read in conjunction with AS/NZS 5601.1:2022 clause 6.10.2.7 which has been updated and now make these requirements mandated.

Trouble shooting guide to assist with the determination of ProblemsTrouble Shooting GuideCloudy or milky colored water:Bad MembraneReplace Membrane and sanitize when below 75% rejectionWater Supply has a high oxygen contentSystem is still newWater does not taste or smell rightBad Membrane – Replace membrane when 75% rejection and sanitizeFilters have expired – Replace filters.©Should replace every 6 to 12 months.System needs sanitizingLow Water OutputIncoming water pressure is below 40 PSI,Increase pressure to 40 psiBad check valve, Replace check valve, Open valve.Filters clogged Replace filtersKinked tube Unkink tube If damaged, replace tubeDocuments / ResourcesPREMIER WATER SYSTEMS 1000 GPD Commercial RO Reverse Osmosis Water Filter System [pdf] Owner's ManualCBBREP32520K85, 600 GPD, 1000 GPD, Commercial RO Reverse Osmosis Water Filter SystemReferences Premier Water Systems | Whole House Water Filtration ProsUser ManualRelated PostsTastePURE Water Filter GuideTastePURE™ Water Filter Guide This is just a partial list of contaminates removed by the TastePURE™ line of…APEC Water Systems RO-QUICK90 System Filter InstructionsRO-QUICK90 System Filter Change Instruction How To Replace Stages 1, 2 Pre-Filters: Turn OFF cold water supply to…GE Shower Water Filter InstructionsGE Shower Water Filter Instruction A REPLACEMENT FOR THE FOLLOWING WATER FILTER: FXSCH FILTER USE: 6 MONTHS OR…Pelican Water Systems WF6/ WF10 Owner's ManualPelican Water Systems WF6/ WF10 Owner's Manual - Download [optimized] Pelican Water Systems WF6/ WF10 Owner's Manual -…

Premier Reverse Osmosisfilters

Always read the manufacturer’s installation instructions to determine the recommended method of connection. As a general rule, appliances that are not designed to be moved should be connected by rigid pipe.

A hose assembly is to hang freely in a ‘U’ shape. Always avoid strain on the hose assembly and its connections. Figure 1 is what a hose assembly should look like when fully installed (including the restraints and buffers).

PREMIER WATER SYSTEMS7623 FULTON AVE | NORTH HOLLYWOOD CA 91605(661) 575 – 0033WWW.PREMIERWATERSYSTEMS.NETCommercial Membrane Installation and Replacement GuideFeed Side of Membrane HousingInsert membrane into housing, making careful to note, which side has the brine seal. The use of a non-petroleum based lubricant is acceptable, if needed.Insert Plug into center hole on brine seal side.Thread Tefloned fitting in to Off-Center hole This will be where the Feed Water is introduced to the membraneProduct Side of Membrane HousingThread the 2 remaining fittings in the “bottom” cap.Insert tube into the off-center fitting, this will be the drain, run tubing to your drain line NOW. Then cut this line and insert the ball valve provided. See diagram above. This valve will need to be adjusted on occasion, so place in an accessible spot, but not where it will be accidentally re-adjusted. Open this valve 1/2 way for now.The Product water (good water) will come out through the center fitting, attach the tube now.Start running water through SLOWLY, turn up the volume SLOWLY, until you are at full volume, do this over a 45 to 60 second period.Run the first few gallons of the Product water to drain to clean the membrane.Then slowly adjust the valve until you have a 1 to 1 ratio of product to water**** in order to have a 1 to 1 ratio you must feed this membrane with softened water, for other hard water or any other water high in TDS you must waste at 2 parts waste to 1 part product waterREPLACEMENT FILTERS:MODEL # CBBREP32520K85WWW.PREMIERWATERSYSTEMS.NETTrouble shooting guide to assist with the determination of ProblemsTrouble Shooting GuideCloudy or milky colored water:Bad MembraneReplace Membrane and sanitize when below 75% rejectionWater Supply has a high oxygen contentSystem is still newWater does not taste or smell rightBad Membrane – Replace membrane when 75% rejection and sanitizeFilters have expired – Replace filters.©Should replace every 6 to 12 months.System needs sanitizingLow Water OutputIncoming water pressure is below 40 PSI,Increase pressure to 40 psiBad check valve, Replace check valve, Open valve.Filters clogged Replace filtersKinked tube Unkink tube If damaged, replace tubeDocuments / ResourcesPREMIER WATER SYSTEMS 1000 GPD Commercial RO Reverse Osmosis Water Filter System [pdf] Owner's ManualCBBREP32520K85, 600 GPD, 1000 GPD, Commercial RO Reverse Osmosis Water Filter SystemReferences Premier Water Systems | Whole House Water Filtration ProsUser ManualRelated PostsTastePURE Water Filter GuideTastePURE™ Water Filter Guide This is just a partial list of contaminates removed by the TastePURE™ line of…APEC Water Systems RO-QUICK90 System Filter InstructionsRO-QUICK90 System Filter Change Instruction How To Replace Stages 1, 2 Pre-Filters: Turn OFF cold water supply to…GE Shower Water Filter InstructionsGE Shower Water Filter Instruction A REPLACEMENT FOR THE FOLLOWING WATER FILTER: FXSCH FILTER USE: 6 MONTHS OR…Pelican Water Systems WF6/ WF10 Owner's ManualPelican Water Systems WF6/ WF10 Owner's Manual - Download [optimized] Pelican Water Systems WF6/ WF10 Owner's Manual -…

WattsPremier Reverse Osmosis

Incoming water pressure is below 40 PSI,Increase pressure to 40 psiBad check valve, Replace check valve, Open valve.Filters clogged Replace filtersKinked tube Unkink tube If damaged, replace tubeDocuments / ResourcesPREMIER WATER SYSTEMS 1000 GPD Commercial RO Reverse Osmosis Water Filter System [pdf] Owner's ManualCBBREP32520K85, 600 GPD, 1000 GPD, Commercial RO Reverse Osmosis Water Filter SystemReferences Premier Water Systems | Whole House Water Filtration ProsUser ManualRelated PostsTastePURE Water Filter GuideTastePURE™ Water Filter Guide This is just a partial list of contaminates removed by the TastePURE™ line of…APEC Water Systems RO-QUICK90 System Filter InstructionsRO-QUICK90 System Filter Change Instruction How To Replace Stages 1, 2 Pre-Filters: Turn OFF cold water supply to…GE Shower Water Filter InstructionsGE Shower Water Filter Instruction A REPLACEMENT FOR THE FOLLOWING WATER FILTER: FXSCH FILTER USE: 6 MONTHS OR…Pelican Water Systems WF6/ WF10 Owner's ManualPelican Water Systems WF6/ WF10 Owner's Manual - Download [optimized] Pelican Water Systems WF6/ WF10 Owner's Manual -…

Similarly, appliances designed with wheels must not have the wheels rendered inoperable so as to avoid the installation of a hose assembly. Wheels may only be replaced with support legs supplied by the appliance manufacturer in accordance with the manufacturer’s specifications.

We acknowledge Victoria's Traditional Owners as the original custodians of the lands on which we work. We offer gratitude and pay respect to Elders past and present.

The hose assembly fixed gas connection should be installed a suitable distance from the appliance connection to create a hanging radius that prevents the hose from kinking.

Fitting wheels or castors to appliances supplied with support legs should only be done with the components supplied by the appliance manufacturer and in accordance with the manufacturer’s specifications.

premierro-pure plusmanual

The appliance isolation valves and regulators must also be accessible for the purpose of isolation, servicing and adjustment. Accessible is defined as access being gained without hazard or undue difficulty. This may be achieved by locating the isolation valve and regulator next to the appliance (for example, beneath a bench) or underneath the appliance but brought forwards for ease of access.

Feed Side of Membrane HousingInsert membrane into housing, making careful to note, which side has the brine seal. The use of a non-petroleum based lubricant is acceptable, if needed.Insert Plug into center hole on brine seal side.Thread Tefloned fitting in to Off-Center hole This will be where the Feed Water is introduced to the membraneProduct Side of Membrane HousingThread the 2 remaining fittings in the “bottom” cap.Insert tube into the off-center fitting, this will be the drain, run tubing to your drain line NOW. Then cut this line and insert the ball valve provided. See diagram above. This valve will need to be adjusted on occasion, so place in an accessible spot, but not where it will be accidentally re-adjusted. Open this valve 1/2 way for now.The Product water (good water) will come out through the center fitting, attach the tube now.Start running water through SLOWLY, turn up the volume SLOWLY, until you are at full volume, do this over a 45 to 60 second period.Run the first few gallons of the Product water to drain to clean the membrane.Then slowly adjust the valve until you have a 1 to 1 ratio of product to water**** in order to have a 1 to 1 ratio you must feed this membrane with softened water, for other hard water or any other water high in TDS you must waste at 2 parts waste to 1 part product waterREPLACEMENT FILTERS:MODEL # CBBREP32520K85WWW.PREMIERWATERSYSTEMS.NETTrouble shooting guide to assist with the determination of ProblemsTrouble Shooting GuideCloudy or milky colored water:Bad MembraneReplace Membrane and sanitize when below 75% rejectionWater Supply has a high oxygen contentSystem is still newWater does not taste or smell rightBad Membrane – Replace membrane when 75% rejection and sanitizeFilters have expired – Replace filters.©Should replace every 6 to 12 months.System needs sanitizingLow Water OutputIncoming water pressure is below 40 PSI,Increase pressure to 40 psiBad check valve, Replace check valve, Open valve.Filters clogged Replace filtersKinked tube Unkink tube If damaged, replace tubeDocuments / ResourcesPREMIER WATER SYSTEMS 1000 GPD Commercial RO Reverse Osmosis Water Filter System [pdf] Owner's ManualCBBREP32520K85, 600 GPD, 1000 GPD, Commercial RO Reverse Osmosis Water Filter SystemReferences Premier Water Systems | Whole House Water Filtration ProsUser ManualRelated PostsTastePURE Water Filter GuideTastePURE™ Water Filter Guide This is just a partial list of contaminates removed by the TastePURE™ line of…APEC Water Systems RO-QUICK90 System Filter InstructionsRO-QUICK90 System Filter Change Instruction How To Replace Stages 1, 2 Pre-Filters: Turn OFF cold water supply to…GE Shower Water Filter InstructionsGE Shower Water Filter Instruction A REPLACEMENT FOR THE FOLLOWING WATER FILTER: FXSCH FILTER USE: 6 MONTHS OR…Pelican Water Systems WF6/ WF10 Owner's ManualPelican Water Systems WF6/ WF10 Owner's Manual - Download [optimized] Pelican Water Systems WF6/ WF10 Owner's Manual -…