The cost of replacing a hot water tempering valve can vary depending on the type of valve, the unit’s size, and the installation’s complexity. In general, however, a tempering valve will cost anywhere between $150 and $200. The labor costs associated with the tempering valve replacement will depend on the plumber’s hourly rate and the time required to complete the job. It is typically possible to complete the work in one to two hours for a standard installation. The total cost of replacing a tempering valve can range from $250 to $600.

Boilerdrain valve for washing machine

I need help with...Blocked drainBurst leaking pipeLeaking tapHot waterLP gas serviceSeptic tank maintenanceProperty maintenanceGeneral plumbingOther

Boilerdrain cap

If you have any other questions regarding tempering valve replacement or tempering valve installation, get in touch with Ironclad Plumbing Blue Mountains. We can help you with hot water repair, installation and maintenance. Give us a call on 02 4760 0441 or fill out the online enquiry form.

Ironclad Plumbing exists to provide our customers with professional plumbing and property services, with the safest and highest quality workmanship. We believe our future success is in building trust with our customers and our community. This can only be done by doing the best possible job first time.

We can handle everything from small repairs to minor plastering and gyprock. So why not give us a call today? Contact us 0474 318 136 or alternatively fill out the contact form to request a callback.

Boiler drainsreplacement

A tempering valve is located externally on the hot water system. It is installed between the cold line and the hot water line. Depending on what type of water heater you have the Tempering Valve can be either orange (used in solar heaters), blue (most likely if you have an electric hot water system), green (gas heaters) or yellow (if you have instantaneous heater)

We service the Great Western Corridor, from Penrith through the Blue Mountains and out to Lithgow. We offer 24/7 service in case of plumbing emergencies. You can count on us to do the job right the first time.

We can help you get your dream kitchen. bathroom, or outdoor area. So why not give us a call today? Contact us 0474 318 136 or alternatively fill out our contact form and we will call you back.

boilerdrain valve 3/4

Environmentally friendly tree removal and land-clearing services in the Blue Mountains, Penrith and Lithgow.  Contact us 0474 318 136 or alternatively fill out our contact form – we will call you back.

The most common sign that your tempering valve is failing is when your hot water suddenly turns cold or vice versa. If you notice that the water temperature in your shower or sink fluctuates for no apparent reason, your tempering valve likely is to blame.

When a hot water tempering valve fails, the water heater will no longer be able to heat the water to the desired temperature. This can lead to many problems, including scalding, water line freeze-ups, and sediment buildup in the tank. Scalding is a serious safety concern, as it can cause severe burns. Water line freeze-ups can also be a problem, as they can cause the pipes to burst. In addition, sediment buildup can lead to the need for more frequent maintenance of the water heater.Â

Boilerdrain Valve repair kit

BoilerDrain valve

The valve should last you a long time, between 5-10 years, so you may not need to replace it before you replace the heater itself. You might get the life of the heater out of it.

There are a few different types of tempering valves on the market, but they all serve the same purpose. While there are a few different designs, all tempering valves use a similar operating principle. A diaphragm or plunger controls the flow of water, and a spring helps keep the valve closed when there is no water flow. As water flows through the valve, the diaphragm is pushed open, allowing hot and cold water to mix. The amount of mixing can be adjusted by adjusting the spring tension.Â

However, TMVs are not mandatory for domestic houses. Instead, there is a tempering valve to control the temperature, but if that fails, you might get scalding hot or freezing cold water.Â

We compiled a list of the most common questions about tempering valves and tempering valve replacement our plumbers get asked. Find the answers below.

boilerdrain valve 1/2

I need help with...Blocked drainBurst leaking pipeLeaking tapHot waterLP gas serviceSeptic tank maintenanceProperty maintenanceGeneral plumbingOther

Installing a tempering valve may seem like an unnecessary expense, it is an important safety measure that can help prevent serious injuries.

Boiler drainsinstallation

Copyright © 2024 Ironclad Plumbing & Property Services | Ironclad Plumbing Blue Mountains | Professional Plumbing and Property Services. Official Fire Halo™ Distributor for Blue Mountains. All rights reserved | This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply | Read our Blog..

In the state of New South Wales, Australia, it is mandatory for all homes and businesses to have a temperature control device installed in their hot water system. A tempering valve is a vital safety component in any domestic hot water system. Without a tempering valve, there is a risk that the water could be too hot, posing a scalding hazard. In addition, a tempering valve helps to regulate water pressure, ensuring that the flow of water is not too high or too low.

Installing a hot water tempering valve is an important safety measure. It ensures that the stored water in your tanks remain safe to use without risking possible burn injuries while also preventing harmful bacteria

Another common symptom of a failing tempering valve is when the water pressure in your home becomes inconsistent. One minute you may have substantial water pressure, and the next, it may be practically non-existent. This can be extremely frustrating, and it’s often a sign that you need a tempering valve replacement.

To keep us safe from hazards such as Legionella, our storage hot water system maintains a temperature of between 60-70 degrees. The tempering valve then mix it hot water with cold water to deliver it at around 50°C.Â

Thermostatic Mixing Valves (TMVs) have a fail-safe. That means it will shut the hot water off if it’s not mixing with cold water. TMV is mandatory for commercial buildings, nursing homes, daycare centers, and commercial buildings where there are elderly, young kids, or disabled people.Â