Image

I have a Watts pressure reducer model N35B 25 to 75 lb range. I can purchase a rebuild kit $20 or buy a new one $60. The Rebuild seems easier since I assume I just replace the internal parts. Is it just as simple as removing the top and placing new parts in. New one would require more plumbing Knowlege since it screws on from both sides. The problem is the pressure creeps up after the water flow is stopped. I am at 100 psi in an hour.Use a little water and it is back to 50 lbs and it creaps up again slowly. Post Edited

Bell & Gossett Energy Efficient circulators (small in-line pumps) for hydronic heating, potable water recirculation (plumbing), and solar thermal applications.  Circulators are cast iron or lead-free bronze constructed with oil lubricated, wet rotor or dry rotor bearings.

I bought 10 of the Watts N35 and 3 of them did exactly like you described. I went back to the Watts 25 AUB and never have a problem. They cost a bit more however. - - - - - - - - - - - - - - - - - - - - Since 1995 (3 years before Google started) PlumbingSupply.com has been THE best plumbing supplier on the web. Please visit our sponsor [www.PlumbingSupply.com]

I have a watts N35B that is 24 years old. I would get 120 PSI in the house and my flow rate at the hose bib was 5 gpm. the pressure would not change when I screwed it in or out. I took it apart. Tons of crap inside. I rebuilt it, cleaning everything, replacing the dried out o rings and washer with ones that I had on hand. The Diaphram was still usable so I reused it. ( I can order one and replace that later ) Put everything back together works just fine. set it at 80 PSI, and get 10 gpm flow rate Look up the regulator diagram on the watts web site. the only specialty tool was a 1 1/8" socket to remove the valve core.

Mineral deposits usually found in municipal water supplies crust up the insides of these valves so bad that a rebuild is frequently unsuccessful.

Image

Bell & Gossett’s complete line of in-line and base-mounted centrifugal pumps and circulators can handle virtually any HVAC requirement. The pumps are engineered for exceptional performance and rugged durability. They are designed for easy maintenance and to be highly energy efficient. The pumps provide reliable operation in a variety of applications, including hydronic heating and cooling systems, industrial, refrigeration, cooling towers and irrigation.

Does the prv have a built in union? What kind of pipe is it copper, plastic or steel? If copper, you can cut the downstream side and back out the male adapters. Then sweat a coupling or use a compression union. Peace out, Kordts

Welcome to Plbg.com (also known as PlumbingForum.com) where plumbing advice, education, information, help and suggestions are provided by some of the most experienced plumbers and plumbing contractors anywhere who all wish to "give back" to society. Since 1996 we have been free without popup or other invasive ads and known to be the best online STRICTLY PLUMBING advice site. If you have questions about plumbing, toilets, sinks, faucets, drains, sewers, water filters, venting, water heating, showers, pumps, and other strictly PLUMBING related issues then you've come to the right place. Please refrain from asking or discussing legal questions, or pricing, or where to find and/or purchase products, or any business issues, or for contractor referrals, or any other questions or issues not specifically related to plumbing. Keep all posts positive and absolutely no advertising. Our site is completely free, without ads or pop-ups and we don't track you. We absolutely do not sell your personal information. We are made possible by:

You can try to rebuild it, but it is not worth my time to do it, since it could cost the customer more to take it apart and redo it, plus the parts, than it would for me to purchase a new valve and install it.

Image

All B&G pumps are manufactured at an iSo 9001- approved facility. Energy Efficient circulators (small in-line pumps) for hydronic heating, potable water recirculation (plumbing), and solar thermal applications. Circulators are cast iron or lead-free bronze constructed with oil lubricated, wet rotor or dry rotor bearings.