GENTEC Australia is a global supplier of quality products to its customers through its innovation and continuous improvement programme over the lifecycle of the product. GENTEC Australia builds quality into product with robust quality system accredited to ISO 9001 and product certification as per ISO Type 5 scheme, which is audited by third party at regular intervals for compliance.

Pressure Regulators, Valves & Controls, Hydronics & Plumbing, including Feed Water Pressure Regulator 1/2 1156F, High Capacity Water Feed Regulator 1..

Blending valvestypes

Shop for Febco 765 PVB Backflow Preventer 1" FPT at Heritage Plus. Come see why we're a trusted landscape and irrigation supply distributor!

Blending valvesfor thermostatic

Disclaimer: The information provided is only a guide, actual product may differ. The information here should not be relied on without clarification with Gentec. Gentec reserves the right to make design changes at any time without notification. *Subject to terms and conditions, available here

Manufactured from forged DZR Brass Available in 400kPa and 600kPa pressure ratings 20mm female connection You can also find other variants' specification ...

Temperature & Pressure (T&P or TPR) safety relief valves for tank-type hot water heaters, storage vessels & indirect tank applications.

Thermostatic mixing valve vs tempering valve

Blending valvesbunnings

The 3/4 backflow preventer is versatile and can be used in a variety of applications. It is commonly used in residential properties, commercial buildings, and ...

Thermostatic mixing valve

thermostatic mixing valve - bunnings

Our quality product supplied, meets and exceeds customers requirements using our quality functional deployment (QFD) initiative. Product range from GENTEC Australia is accredited for various international and local certification scheme, verifying its continual commitment to meet various regulatory requirements. GENTEC’s quality is the commitment to our customer guaranteed.

Model LFN36-M1. Vacuum Relief Valve. Sizes: 1⁄2" – 3⁄4" Male NPT. Features. • Low profile. • All Lead Free* brass body. • Protective cap.

202495 — Founded in 1988, IWT offers a wide range of services across water treatment applications, including cooling tower & boiler water treatment, ...

Tempering valve

Buy the Watts 0004646 N/A Direct. Shop for the Watts 0004646 N/A 1/2" Automatic Washing Machine Shutoff Valve With Leak Sensor and Inlet Adapters and save.

1101.12.2.2.2 Combined System. The secondary roof drains shall connect to the vertical piping of the primary storm drainage conductor downstream of the last horizontal offset located below the roof. The primary storm drainage system shall connect to the building storm water that connects to an underground public storm sewer. The combined secondary and primary roof drain systems shall be sized in accordance with Section 1103.0 based on double the rainfall rate for the local area.

Blending valvespdf

Today, in addition to a full range of pipeline and specialty strainers, the company manufactures a broad offering of check valves and butterfly valves. Y ...

The secondary roof drain piping can be installed using the method in either Section 1101.12.2.2.1 or Section 1101.12.2.2.2. The secondary piping may be an entirely independent system consisting of roof drains, conduits and leaders, which independently discharge to the outside of the building. This secondary system is a mirror of the primary system, sized and piped identical to the primary system. If this method is used, the primary drainage piping must be piped to the curb, gutter or other approved area. The secondary system, basically an emergency overflow system, can be piped to an open area even if it is a walkway or other traveled outside area. The reason for this is that the secondary system should seldom be used, and if it is used, it would give a warning that something is wrong with the primary system. This secondary piped system gives the owner of the building the largest margin of safety for the building and its occupants.

We are committed to delivering superior customer service to our end customers. Learn more about our comprehensive after-sales support and the resources available.

The other method of secondary roof drainage piping is to connect the secondary roof drains to the piping serving the primary roof drains (see Figures 1101.12.2.2.2a, 1101.12.2.2.2b and 1101.12.2.2.2c). The connection of the secondary drain must be in a vertical section of piping downstream of any horizontal piping below the roof. If this method is used the size of the conduits, leaders and downspouts downstream of the connection must be increased by using twice the rainfall rate required for the primary piping. For example, if the rainfall rate for the area is 3 inches per hour the size of the combined piping system must be calculated using 6 inches of rainfall per hour.

incoming water pressure and improve the RO efficiency. ○ Maximum water pressure: 70 PSI, otherwise a pressure regulator (part no. APR70) is required to ...

You will continue to receive e-mail notifications from us until such time as you unsubscribe. To make sure these e-mails are not sent to your bulk or junk mail folders, add news@iapmo.org to your address book. Requests for new subscriptions or change of e-mail address should be sent to news@iapmo.org. IAPMO does not knowingly participate in SPAM. We do not sell, rent or trade the names on our e-mail list; your e-mail address is only used to send messages from IAPMO. If you wish to be removed from this list, follow the link below.